Gree GWH07AWAXA-K6DNA1C

65
Technical Information
Service Manual
● Set temperature range from remote controller: 16~30°C(61-
86°F).
● This mode indicator is not available for some models.
● Cooling only unit won't receive heat mode signal. If setting
heat mode with remote cont roller, press "
" button can't start
up the unit.
3. Fan button
This button is used for setting Fan Speed in the sequence that
goes from AUTO,
, , , , , , then back to
Auto.
NOTE:
● Under AUTO speed, air conditioner will select proper fan
speed automatically according to factory default setting.
● It's low fan speed under dry mode.
● X-FAN function: Holding fan speed button for 2 seconds
in cool or dry mode, the icon "
" is displayed and the indoor
fan will continue operation for a few minutes in order to dry
the indoor unit even though you have turned off the unit. After
energization, X-FAN OFF is defaulted. X-FAN is not available in
auto, fan or heat mode.
This function indicates that moisture on evaporator of indoor
unit will be blowed after the unit is stopped to avoid mould.
● Having set X-FAN function on: After turning off the unit by
pressing "
" button, indoor fan will continue running for a few
minutes at low speed. In this period, hold fan speed button for 2
seconds to stop indoor fan directly. Having set X-FAN function
off: After turning off the unit by pressing "
" button, the
complete unit will be off directly.
4. - / + button
Press "+" or "-" button once increase or decrease set
temperature 1°C(°F). Holding "+" or "-" button, 2 seconds later,
set temperature on remote controller will change quickly. On
releasing button after setting is finished, temperature indicator
on indoor unit will change accordingly. (Temperature can't be
adjusted under auto mode)
When setting TIMER ON, TIMER OFF or CLOCK, press "+" or "-"
button to adjust time. (Refer to CLOCK, TIMER ON, TIMER OFF
functions).
5. MENU button
Press this button to select submenu function and then press
"SET" button to set the function status of submenu. The submenu
can be selected circularly as follows:
blank
No Setting
/
TIMER
OFF
TIMER
ON
NOTE:
● Some menu's function may be unavailable under different
models.
Light function
When selecting light function, light icon " " flashes for
5 seconds; press "SET" button within 5 seconds to turn off
display light on indoor unit and "
" icon on remote controller
disappears. Press "SET" button again within 5 seconds to turn on
display light and "
" icon is displayed.
Sleep function
When selecting sleeping function, sleeping icon " " ashes for
5 seconds; press "SET" button within 5 seconds can select Sleep
1 (
1), Sleep 2 ( 2), Sleep 3 ( 3) and cancel Sleep circularly.
● Sleep 1 is Sleep mode 1, in Cool modes; sleep status after run
for one hour, the main unit setting temperature will increase 1°C,
two hours, setting temperature increased 2°C, then the unit will
run at this setting temperature; In Heat mode: sleep status after
run for one hour, the setting temperature will decrease 1°C, two
hours, setting temperature will decrease 2°C, then the unit will
run at this setting temperature.
● Sleep 2 is sleep mode 2, that is air conditioner will run
according to the presetting a group of sleep temperature curve.
● Sleep 3-the sleep curve setting under Sleep mode by DIY;
(1) Under Sleep 3 mode, press "Turbo" button for a long
time, remote controller enters into user individuation sleep
setting status, at this time, the time of remote controller will
display "1hour", the setting temperature "88" will display the
corresponding temperature of last setting sleep curve and blink
(The rst entering will display according to the initial curve setting
value of original factory);
(2) Adjust "+" and "-" button, could change the corresponding
setting temperature, after adjusted, press "Turbo" button for
conrmation;
(3) At this time, 1hour will be automatically increased at the timer
position on the remote control, (that are "2hours" or "3hours" or
"8hours"), the place of setting temperature "88" will display the
corresponding temperature of last setting sleep curve and blink;
(4) Repeat the above step (2)~(3) operation, until 8 hours
temperature setting nished, sleep,curve setting nished, at this
time, the remote controller will resume the original timer display;
temperature display will resume to original setting temperature.
● Sleep3- the sleep curve setting under Sleep mode by DIY could
be inquired:
The user could accord to sleep curve setting method to inquire
the presetting sleep curve, enter into user individuation sleep