Gree GWH07AWAXA-K6DNA1C

66
Technical Information
Service Manual
setting status, but do not change the temperature, press "Turbo"
button directly for conrmation. Note: In the above presetting or
enquiry procedure, if continuously within 10 seconds, there is
no button pressed, the sleep curve setting within 10 seconds,
there is no button pressed, the sleep curve setting status will be
automatically quit and resume to display the original displaying. In
the presetting or enquiry procedure, press "
" button, "MODE"
button, the sleep curve setting or enquiry status will quit similarly.
TIMER ON function
TIMER ON function can set the time for timer on. Under TIMER
ON function status, " " icon disappears and the word "ON" on
remote controller blinks. Press "+" or "-" button to adjust TIMER
ON setting. After each pressing "+" or "-" button, TIMER ON
setting will increase or decrease 1minute. Hold "+" or "-" button,
2 seconds later, the time will change quickly until reaching your
required time. Press "SET" button to conrm it within 5 seconds.
The word "ON" will stop blinking.
Cancel TIMER ON: Press "MENU" button to TIMER ON function
and the characters "ON" ashes on the remote controller; press
"SET" button until the characters "ON" disappears.
TIMER OFF function
TIMER OFF function can set the time for timer off. Under TIMER
OFF function status, " " icon disappears and the word "OFF" on
remote controller blinks. Press "+" or "-" button to adjust TIMER
OFF setting. After each pressing "+" or "-" button, TIMER OFF
setting will increase or decrease 1minute. Hold "+" or "-" button,
2 seconds later, the time will change quickly until reaching your
required time, press "SET" button to conrm it within 5 seconds.
The word "OFF" will stop blinking.
Cancel TIMER OFF: Press "MENU" button to TIMER OFF
function and the characters "OFF" flashes on the remote
controller; press "SET" button until the characters "OFF"
disappears.
CLOCK function
CLOCK function can set clock time. Under CLOCK function
status, " " icon on remote controller will blink. Press "+" or "-"
button within 5 seconds to set clock time. Each pressing of "+"
or "-" button, clock time will increas e or decrease 1 minute. If
hold "+" or "-" button, 2 seconds later, time will change quickly.
Release this button when reaching your required time, press
"SET" button to conrm it within 5 seconds. The "
" icon will
stop blinking.
Left & right swing function
When selecting left & right swing function, left & right swing icon
" " ashes for 5 seconds; press "SET" button within 5 seconds
to select left & right swing angle.
Fan blow angle can be selected circularly as below:
no display
position)
(stops at current
NOTE:
● The function is only available for some models.
I FEEL function
When selecting I FEEL function, I FEEL icon " " flashes for
5 seconds. Press "SET" button to start I FEEL function within
5 seconds and "
" will be displayed on the remote controller.
After this function is set, the remote controller will send the
detected ambient temperature to the controller and the unit will
automatically adjust the indoor temperature according to the
detected temperature. Press "SET" button again to cancel I FEEL
function and "
" will disappear.
Please put the remote controller near user when this function
is set. Do not put the remote controller near the object of high
temperature or low temperature in order to avoid detecting
inaccurate ambient temperature.When I FEEL function is turned
on, the remote controller should be put within the area where
indoor unit can receive the signal sent by the remote controller.
Energy-saving function
Under cooling mode, when selecting energy-saving function,
energy-saving function icon " " ashes for 5 seconds; press
"SET" button within 5 seconds to turn on or turn off energy-saving
function. When energy-saving function is started up, "SE" will be
shown on remote controller, and air conditioner will adjust the set
temperature automatically according to ex-factory setting to reach
to the best energy-saving effect. Press "SET" button again to exit
energy-saving function.
8°C-heating function
Under heating mode, when selecting 8°C-heating function,
8°C-heating icon " " ashes for 5 seconds; press "SET" button
within 5 seconds to turn on or turn off 8°C-heating. When
8°C-heating is started up, "
" will be shown on remote controller,
and the air conditioner keep the heating status at 8°C. Press
"SET" button again to exit 8°C-heating function.
NOTE:
● Under °F temperature display, the remote controller will
display 46°F heating.
Power limiting function
Power limiting function is for limiting the power of the whole
unit. When selecting power limiting function, power limiting icon
"
" ashes for 5 seconds; press "SET" button within 5 seconds
and the remote controller will circularly display as follows: