Grizzly G0640X - Aligning Fence; Miter Gauge

"'+"
BdYZa<%+)%MB[\#H^cXZ&$%.
I]Z [ZcXZ bjhi WZ eVgVaaZa id i]Z b^iZg hadi ^c
dgYZgidn^ZaYVXXjgViZgZhjaih#
To check/align the fence parallel with the
miter slot:
1. Bdjci i]Z [ZcXZ cZmi id i]Z b^iZg hadi VcY
ZmVb^cZi]ZZY\Zhd[ZVX]#
·>[ i]Z [ZcXZ ^h eVgVaaZa l^i] i]Z b^iZg hadi!
i]ZccdVY_jhibZcihVgZcZXZhhVgn#
·>[ i]Z[ZcXZ^hCDIeVgVaaZa l^i]i]Zb^iZg
hadi!Xdci^cjZidStep 2#
2. AddhZc i]Z [djg XVe hXgZlh adXViZY dc i]Z
ide[VXZd[i]Z[ZcXZFigure 30#
Figure 30.;djg[ZcXZXVehXgZlh#
I]Z b^iZg \Vj\Z cZZYh id WZ XVa^WgViZY id i]Z
WaVYZl]Zc^i^h[^ghibdjciZY^ci]Zb^iZghadi#
To calibrate the miter gauge:
1. EaVXZ V bVX]^c^hih hfjVgZ dc i]Z iVWaZ hd
dcZZY\Z^hZkZcanidjX]^c\i]ZWaVYZ[VXZ!
Vhh]dlc^cFigure 31!VcYi]Zdi]ZgZY\Z^h
idjX]^c\i]Zb^iZg\Vj\Z#
2. AddhZc i]Z adX` `cdW dc i]Z b^iZg \Vj\Z
VcYVY_jhi^ijci^a[ajh]l^i]i]ZZY\Zd[i]Z
hfjVgZ#
3. I^\]iZci]ZadX``cdW!VcYkZg^[ni]ZhZii^c\#
 Note: Sometimes the tightening procedure
can affect the adjustment.
4. 6Y_jhii]ZhidehXgZlVcYgZaViZYadX`cjidc
i]ZjcYZgh^YZ d[i]Zb^iZg\Vj\Z#I]^hhide
hXgZlVaadlhi]Zb^iZg\Vj\ZidgZijgcidi]Z
ZmVXibZVhjgZbZcigZeZViZYanl^i]djijh^c\
i]ZhfjVgZ#
5. AddhZc i]Z hXgZl i]Vi hZXjgZh i]Z Vc\aZ
ed^ciZgVcYVY_jhii]Zed^ciZgidi]Z%bVg`
dci]ZhXVaZ#
6. GZi^\]iZc i]Z hXgZl i]Vi hZXjgZh i]Z Vc\aZ
ed^ciZg#
7. GZeZVi Steps 1–4 l^i] i]Z ild )* hideh!
jh^c\V)*hfjVgZVhV\Vj\Z#
Figure 31. HfjVg^c\b^iZg\Vj\ZidWaVYZ#
3. 6Y_jhii]Z[ZcXZ[VXZeVgVaaZal^i]i]ZZY\Zd[
i]Zb^iZghadi#
4. I^\]iZci]Z[djgXVehXgZlh!WZ^c\XVgZ[jacdi
idbdkZi]Z[ZcXZ#
NOTICE
Adjusting the fence parallel to the miter slot
does not guarantee straight cuts. The miter
slot may need to be adjusted parallel to the
side of the blade, which is covered in the
Aligning Table instructions on Page 25.
Aligning Fence Miter Gauge