Grizzly G1023 User Manual (English)

Other manuals for Grizzly G1023

Questions and Answers:

J
Jorge MoralesAug 17, 2025
What to do if Grizzly G1023 Saw motor won't start and fuses or circuit breakers blow?
- M
  Margaret GarciaAug 18, 2025
  If the fuses or circuit breakers blow when you try to start the Grizzly Saw motor, there are several potential causes. First, inspect the line cord or plug for damaged insulation and shorted wires. Second, check all connections on the motor for loose or shorted terminals or worn insulation. Finally, make sure that you have the correct fuses or circuit breakers installed in the power line; if not, install the correct ones.
K
kevinnormanAug 20, 2025
What to do if Grizzly Saw motor stalls and blows fuses?
- S
  samantharamirezAug 20, 2025
  If your Grizzly Saw motor stalls, resulting in blown fuses or a tripped circuit, there are several possible reasons. First, inspect the connections on the motor for loose or shorted terminals or worn insulation. Second, address any low voltage conditions. Third, ensure that the correct fuses or circuit breakers are installed in the power line; if not, install the correct ones. Lastly, reduce the load on the motor if it is overloaded.
C
Christopher SalazarAug 22, 2025
Why does my Grizzly Saw motor overheat?
- G
  George PatrickAug 22, 2025
  If the Grizzly Saw motor overheats, it could be due to a couple of reasons. One reason is that the motor is overloaded, in this case you should reduce the load on the motor. Another possible reason is restricted air circulation through the motor, so you should clean out the motor to allow normal air circulation.
J
Jeffrey BrownAug 26, 2025
How to troubleshoot a Grizzly Saw motor that will not start?
- M
  Melanie CordovaAug 26, 2025
  If the Grizzly Saw motor won't start, there are a couple of things to check. First, verify the power line for proper voltage. Second, inspect all lead connections on the motor for loose or open connections.
K
karen30Aug 27, 2025
Why is my Grizzly G1023 Saw making a loud, repetitive noise?
- J
  Joel WeaverAug 27, 2025
  If you hear a loud, repetitious noise coming from the Grizzly Saw, consider the following: 1. Inspect the keys and setscrews, replace or tighten if necessary, as they may be missing or loose. 2. Tighten the fan or shim the cover, as the motor fan might be hitting the cover. 3. Replace the V-belts if they are defective.
K
Kristy ArmstrongAug 30, 2025
Why is the blade on my Grizzly Saw not square with the miter slot?
- D
  Danielle HamiltonAug 30, 2025
  If the blade is not square with the miter slot or the fence is not square to the blade on your Grizzly Saw, it could be due to a few reasons. The blade might be warped, in which case you should replace it. Alternatively, the table top may not be parallel to the blade, or the fence may not be parallel to the blade.
R
Raymond TorresSep 1, 2025
What to do if Grizzly G1023 slows down when operating?
- O
  odrakeSep 2, 2025
  If the Grizzly Saw slows down during operation, you should feed the workpiece slower.
C
carolinekellySep 4, 2025
What to do if Grizzly G1023 Saw blade does not reach 90°?
- J
  Joseph WrightSep 4, 2025
  If the blade on your Grizzly Saw does not reach 90 degrees, it could be because the 90° stop bolt is out of adjustment, or the pointer bracket is hitting before the blade reaches 90°. In the second case, you should file down the right side of the pointer bracket until the blade can reach 90°.
C
carpenterkelseySep 6, 2025
Why won't the hand wheels turn on my Grizzly G1023?
- B
  Bryan Sullivan DDSSep 7, 2025
  If the hand wheels on your Grizzly Saw won’t turn, there are a few potential causes. First, the hand wheel key might be inserted too far; remove the hand wheel and adjust the key. Second, the bullets might be wedged; remove the hand wheel and adjust the bullets. Third, the roll pin or setscrew in the worm gear might be contacting the geared trunnion; inspect the roll pins and setscrews in the worm gear and tighten if necessary.
J
jeremy47Sep 9, 2025
Why does the blade on my Grizzly G1023 hit the insert at 45 degrees?
- R
  Randy ConnerSep 9, 2025
  If the blade hits the insert at 45° on your Grizzly Saw, it could be due to several reasons. The hole in the insert might be inadequate, so you should file or mill the hole in the insert. Alternatively, the table could be out of alignment, or the blade position could be incorrect.