Grizzly G4000 User Manual (English)

Other manuals for Grizzly G4000

Owner's Manual76 pages

Parts List24 pages

Questions and Answers:

R
Robert ScottAug 14, 2025
How to fix a bad surface finish on a Grizzly Lathe?
- E
  Elizabeth LindseyAug 14, 2025
  A bad surface finish on your Grizzly Lathe can occur due to several reasons. First, the spindle speed or feed rate might be incorrect, so you should adjust them. Second, the tool might be dull or the wrong one for the job, so use sharp tools and the correct tool for the operation. Third, too much play in the gibs can cause this issue, so adjust the gibs. Finally, the tool might be too high, so lower its position.
D
Darlene ValdezAug 17, 2025
Why does my Grizzly G4000 vibrate excessively during cutting?
- V
  vwangAug 17, 2025
  Excessive vibration during cutting with your Grizzly Lathe can be caused by several factors. Ensure the tool holder is sufficiently tight and free of debris. If the cutting tool extends too far from the holder, reinstall it so that no more than 1/3 of its total length is exposed. Also, too much play in the gibs can cause vibration, so adjust them. A dull cutting tool can also cause vibration, so sharpen or replace it. Finally, incorrect spindle speed or feed rate may be the issue, so adjust accordingly.
J
Joyce SotoAug 20, 2025
What to do if the cross/compound slide or carriage feed is hard to move on my Grizzly G4000 Lathe?
- J
  Jennifer FisherAug 20, 2025
  If the cross/compound slide or carriage feed on your Grizzly Lathe is hard to move, several factors could be responsible. The gibs might be loaded with chips or grime; in this case, remove the gibs, clean the ways, lubricate, and properly adjust the gibs. Alternatively, the gibs might be too tight, so adjust them. If it is a cross slide, the leadscrew backlash setting might be too tight, so properly adjust it. Dirty or dry bedways can also cause this issue, so clean and lubricate them. Lastly, the gearing might be at fault, so inspect and replace if necessary.
G
gbrownAug 25, 2025
Why is the cross/compound slide or carriage feed sloppy on my Grizzly Lathe?
- S
  Sheryl JoyceAug 25, 2025
  If the cross/compound slide or carriage feed on your Grizzly Lathe has sloppy operation, it could be due to several reasons. Too much play in the gibs can cause this, so adjust them. Loose handwheels can also be a factor, so tighten the handwheel fasteners. If it is a cross slide, too much leadscrew backlash can cause this, so adjust the leadscrew backlash. Finally, the leadscrew mechanism might be worn or out of adjustment, so tighten any loose fasteners and check for excessive wear, replacing if necessary.
M
Michelle ColonAug 27, 2025
What to do if I cannot remove a tapered tool from the tailstock quill of my Grizzly Lathe?
- P
  Patrick RangelAug 27, 2025
  If you cannot remove a tapered tool from the tailstock quill of your Grizzly Lathe, it could be due to the quill not being fully retracted. Rotate the quill handwheel until the tapered tool is forced out. Another possibility is debris or oil on the tapered mating surfaces, so always ensure these surfaces are clean before inserting the tool.
M
Mary TerryAug 31, 2025
Why won't the chuck jaws move easily on my Grizzly G4000 Lathe?
- J
  Jennifer WeissAug 31, 2025
  If the chuck jaws on your Grizzly Lathe will not move or do not move easily, it is likely due to chips or debris lodged in the jaws. Remove the jaws, clean and lubricate the jaws, scroll-gear threads, and chuck, then replace the jaws.
A
Anthony BrownSep 3, 2025
What causes inaccurate turning results on my Grizzly G4000 Lathe?
- H
  Haley HallSep 3, 2025
  Inaccurate turning results from one end of the workpiece to the other on your Grizzly Lathe is caused by the tailstock not being properly aligned with the headstock.
J
Joshua MoralesSep 6, 2025
What to do if gear(s) will not line up and mesh on my Grizzly G4000?
- G
  Grant PayneSep 6, 2025
  If the gears on your Grizzly Lathe will not line up and mesh, it is because the gears are not aligned. Rotate the spindle by hand until the gears fall into place.
G
Gregory BeardSep 9, 2025
Why will the tailstock quill not feed out of the tailstock on my Grizzly G4000 Lathe?
- E
  Edward LeachSep 10, 2025
  If the tailstock quill will not feed out of the tailstock on your Grizzly Lathe, it is probably because the quill lock is tightened down. Turn the quill lock counterclockwise to loosen it.