EasyManuals Logo

Grundfos CU 241 User Manual

Grundfos CU 241
30 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #5 background imageLoading...
Page #5 background image
English (GB) Installation and operating instructions
Original installation and operating instructions
Table of contents
1. General information ......................................................................6
1.1 Hazard statements........................................................................6
1.2 Notes ................................................................................6
2. Installing the product .....................................................................6
2.1 Location ..............................................................................6
2.2 Mechanical installation .....................................................................7
2.3 Electrical connection...................................................................... 11
3. Starting up the product ................................................................... 11
3.1 Connecting to Grundfos GO Remote............................................................ 11
3.2 Startup wizard on Grundfos GO Remote ......................................................... 11
3.3 Startup wizard on the operating panel ........................................................... 11
3.4 How to enable Bluetooth on the operating panel..................................................... 11
3.5 How to disable Bluetooth on the operating panel ....................................................12
3.6 Testing the product.......................................................................12
4. Product introduction.....................................................................12
4.1 Product description ......................................................................12
4.2 Intended use ..........................................................................12
4.3 Features .............................................................................12
4.4 Application types ........................................................................12
4.5 Terminals ............................................................................14
4.6 Identification...........................................................................14
4.7 Supported communication interface modules and protocols ..............................................15
5. Control functions .......................................................................15
5.1 Operating panel ........................................................................15
6. Setting the product......................................................................16
6.1 Setting the application type with Grundfos GO Remote.................................................16
6.2 Setting the sensor type ....................................................................16
6.3 Setting the start level .....................................................................16
6.4 Setting the stop level .....................................................................17
6.5 Setting the high level .....................................................................17
6.6 Stop delay ............................................................................18
6.7 Power-on delay.........................................................................18
6.8 Dry-running protection.....................................................................18
6.9 "Multipump settings" ......................................................................18
6.10 Using the same level switch for the start and stop level ................................................18
6.11 "Antiseizing"...........................................................................19
6.12 Signal-detection time .....................................................................19
6.13 Setting the maximum number of restarts with Grundfos GO Remote ........................................19
6.14 Setting the service interval with Grundfos GO Remote .................................................19
6.15 Motor protection ........................................................................19
6.16 Alarm reset ...........................................................................20
6.17 Setting the buzzer with Grundfos GO Remote ......................................................20
6.18 Setting units for Grundfos GO Remote...........................................................20
6.19 Setting units for the operating panel with Grundfos GO Remote ...........................................21
6.20 GENIbus .............................................................................21
6.21 Security .............................................................................21
6.22 Starting the startup wizard with the operating panel ...................................................22
7. Operating the product....................................................................22
7.1 Manual operation........................................................................22
8. Servicing the product ....................................................................23
8.1 Updating the product software................................................................23
8.2 Replacing the control unit...................................................................23
8.3 Replacing the CIM module ..................................................................23
8.4 Replacing the battery .....................................................................23
9. Fault finding the product ..................................................................24
9.1 Overview of alarm and warning codes ...........................................................24
9.2 Code 2 (Power phase missing) ...............................................................24
9.3 Code 4 (Too many motor restarts) .............................................................24
9.4 Code 9 (Power phase sequence wrong)..........................................................24
9.5 Code 12 (Service needed) ..................................................................25
9.6 Code 22 (Moisture in motor of pump) ...........................................................25
5
English (GB)

Table of Contents

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Grundfos CU 241 and is the answer not in the manual?

Grundfos CU 241 Specifications

General IconGeneral
BrandGrundfos
ModelCU 241
CategoryControl Unit
LanguageEnglish

Related product manuals