GSI Group - Laser Division
JK300HP/JK300P/JK125P
Issue 2.0 Pre-installation and User Manual
Part No: 1EA300E01 Page xi
7.5.8
Alarm 3n08: High temperature fault .................................................... 87
7.5.9 Alarm 3n09: Very High temperature fault............................................ 87
7.5.10 Alarm 3n10: High Conductivity fault .................................................... 88
7.5.11 Alarm 3n11: Low Coolant Flow ........................................................... 88
7.5.12 Alarm 3n12: High Coolant Flow .......................................................... 88
7.5.13 Alarm 3n13: Temperature Sensor Fault.............................................. 88
7.5.14 Alarm 3n14: Conductivity Sensor Fault............................................... 89
7.6 Power Supply Alarms (Zone 4) ......................................................................... 89
7.6.1 Alarm 4n01 : Power Supply Module communication fault................... 89
7.6.2 Alarm 4n02 : Power Supply Software Error ........................................ 89
7.6.3 Alarm 4n03 : Power Supply Negative 15 Volt Fault ........................... 89
7.6.4 Alarm 4n04 : Power Supply Fan Fault ................................................ 89
7.6.5 Alarm 4n05 : Power Supply Over Temperature .................................. 90
7.6.6 Alarm 4n06 : Power Supply Contactor In Fault ................................... 90
7.6.7 Alarm 4n07 : Power Supply Failed to initialise .................................... 90
7.6.8 Alarm 4n08 : Power Supply Contactor In Timeout .............................. 90
7.6.9 Alarm 4n09 : Power Supply Failed To Simmer .................................. 90
7.6.10 Alarm 4n10 : Power Supply Failed To Simmer Timeout ..................... 91
7.6.11 Alarm 4n11 : Power Supply Simmer Under Power Fault. ................... 91
7.6.12 Alarm 4n12 : Power Supply Simmer Over Power Fault ...................... 91
7.6.13 Alarm 4n13 : Power Supply Failed To Enable ................................... 91
7.6.14 Alarm 4n14 : Power Supply Limit Fault .............................................. 91
7.6.15 Alarm 4n15 : Power Supply IGBT Fault .............................................. 92
7.6.16 Alarm 4n16 : Power Supply Earth Fault .............................................. 92
7.6.17 Alarm 4n17 : Power Supply Input Voltage Loss.................................. 92
7.6.18 Alarm 4n18 : Power Supply Contactor Out Fault ................................ 92
7.6.19 Alarm 4n19 : Power Supply Shutdown During Operation ................... 92
7.6.20 Alarm 4n20 : Power Supply Contactor Out Timeout ........................... 93
7.6.21 Alarm 4n21 : Power Supply Residual Voltage Fault ........................... 93
7.7 Shutter Alarms (Zone 5).................................................................................... 93
7.7.1 Alarm 5n01 : Shutter communication fault .......................................... 93
7.7.2 Alarm 5n02 : Shutter Initialisation Failure ........................................... 93
7.7.3 Alarm 5n03 : Shutter Configuration Failure......................................... 94
7.7.4 Alarm 5n05 : Shutter Emergency Stop Fault....................................... 94
7.7.5 Alarm 5n06 : Shutter Close Fault ........................................................ 94
7.8 Machine Interface Alarms (Zone 6)................................................................... 94
7.9 Warning Number Allocation .............................................................................. 95
7.10 System Level Warnings (Zone 1)...................................................................... 95
7.10.1 Warning 1n01 : Serial Link Buffer Overflow ........................................ 95
7.10.2 Warning 1n02 : Laser Control Card Communications Overflow.......... 95
7.10.3 Warning 1n03 : Incorrect packet data ................................................. 95
7.10.4 Warning 1n04 : Data Over Range....................................................... 95
7.10.5 Warning 1n05 : Shutter Communications Timeout ............................. 96
7.10.6 Warning 1n06 : Sector Over Range .................................................... 96
7.10.7 Warning 1n07 : Operating Envelope Over Range............................... 96
7.10.8 Warning 1n08 : High Output Trip ........................................................ 96
7.10.9 Warning 1n09 : Low Output Trip ......................................................... 96
7.10.10 Warning 1n10 : Shot Limit Exceeded.................................................. 96
7.10.11 Warning 1n11 : Shutter Multi Pulse External Trigger Timeout ............ 96
7.10.12 Warning 1n12 : Shutter Multi shot or Single shot not allowed while
laser is off ........................................................................................... 97
7.11 Cooler Warnings (Zone 3)................................................................................. 97
7.11.1 Warning 3n01 : Low Temperature...................................................... 97
7.11.2 Warning 3n02 : High Temperature..................................................... 97
Petitioners Canadian Solar Inc. and Canadian Solar (USA) Inc.
Ex. 1025, p. xi
To Next Page
Loading...
Need help?
General
