EasyManua.ls Logo

GYS EASYMIG 110 - User Manual

GYS EASYMIG 110
80 pages
Go to English
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
FR
EN
DE
ES
RU
NL
IT
2-10 / 65-80
11-19 / 65-80
20-28 / 65-80
29-37 / 65-80
38-46 / 65-80
47-55 / 65-80
56-64 / 65-80
EASYMIG 110
EASYMIG 130
EASYMIG 140
EASYMIG 150
Poste à souder MIG
MIG/MAG Welding
Schutzgasschweißgerät
Soldadura MIG
Аппараты MIG
MIG Lasapparaat
Machina di saldatura MIG
www.gys.fr
C51348ind7_21/01/2019

Table of Contents

Other manuals for GYS EASYMIG 110

Preview: User Manual
User Manual88 pages

Questions and Answers

  • B
    Brandon RuizSep 6, 2025
    How to fix the welding wire speed if it is not constant in my GYS Welding System?
    • J
      Jason AnthonySep 6, 2025
      Inconsistent welding wire speed can be caused by: * Debris blocking the opening; clean out or change the contact batch and replace the anti-adherence product (Ref.041806). * The wire skidding in the rollers. To resolve this: * Control or replace the roller. * Ensure the wire diameter is compatible with the roller. * Verify the covering wire guide in the torch is compatible.
  • D
    Dennis WilcoxAug 22, 2025
    Why are there very important flashing particles when using my GYS EASYMIG 110 Welding System?
    • L
      Laura BradfordAug 22, 2025
      If you notice very important flashing particles during welding with your GYS Welding System, it could be due to several reasons. First, the arc voltage might be too low or too high, so check the welding settings. Second, there might be a bad earth connection, ensure the earth cable has a proper connection. Lastly, insufficient gas flow can cause this issue, adjust the gas flow to the correct level.
  • D
    davidhallSep 3, 2025
    How to troubleshoot bad wire feeding on my GYS EASYMIG 110 Welding System?
    • A
      ann82Sep 4, 2025
      If you're experiencing bad wire feeding, consider these possible causes and solutions: * The covering wire guide might be dirty or damaged; clean or replace it. * The drive roller may be too loose; tighten the drive roller knob. * The reel brake might be too tight; release the brake. * There could be a bad connection to the main supply; check the mains connection and ensure the plug is fed by a 230 V (1PH) power socket. * A bad earth connection could be the issue; check the earth cable (connection and clamp condition).
  • C
    Clayton MccarthySep 2, 2025
    What to do if the wire-feeder motor doesn’t operate on my GYS EASYMIG 110 Welding System?
    • V
      Vincent HernandezSep 2, 2025
      If the wire-feeder motor isn’t working, check these potential causes: * The reel or roller brake might be too tight; release the brake and rollers. * There could be an electrical supply problem; ensure the power switch is in the "On" position.
  • C
    Christopher ChavezSep 1, 2025
    Why is there no gas flow at the end of the torch on my GYS EASYMIG 110 Welding System?
    • E
      Elizabeth MartinSep 1, 2025
      If there is no gas flow at the end of the torch of your GYS Welding System, it could be due to a bad gas connection. Check the gas connection at the welding machine, the gas regulator, and the solenoid valves.
  • L
    levyjoeAug 30, 2025
    Why doesn't the wire-feeder motor operate on my GYS EASYMIG 110?
    • Q
      qscottAug 30, 2025
      If the wire-feeder motor doesn’t operate on your GYS Welding System, it could be due to a reel or roller brake being too tight. Release the brake and rollers. Another potential cause is an electrical supply problem. Check that the power switch is in the "On" position.
  • L
    Lance FieldsAug 29, 2025
    What causes wire jams after the rollers in a GYS Welding System?
    • A
      Angela MejiaAug 29, 2025
      If the wire jams after the rollers in your GYS Welding System, start by checking the sheath and torch body for a crushed guide wire sheath. Also, check for wire jammed in the torch, clean or replace if necessary. Ensure the presence of a capillary tube. If the wire speed is too fast, reduce the wire speed.
  • H
    heidi35Aug 27, 2025
    Why is there no welding current in my GYS Welding System?
    • B
      Bobby BarkerAug 27, 2025
      If your GYS Welding System has no welding current, there are several things to check. First, ensure there isn't a bad connection to the main supply. Check the mains connection and verify the plug is fed by a 230 V (1PH) power socket. Second, inspect the earth cable for a bad earth connection, checking both the connection and clamp condition. Finally, check if the torch trigger is inoperative; if so, check the torch trigger and replace the torch if needed.
  • E
    Elizabeth RamosAug 26, 2025
    How to troubleshoot inconsistent welding wire speed on a GYS EASYMIG 110?
    • B
      Brian HessAug 27, 2025
      If the welding wire speed is not constant on your GYS Welding System, it could be due to debris blocking the opening; clean out the contact batch or change it and replace the anti-adherence product Ref.041806. Alternatively, the wire might be skidding in the rollers. In this case, control the roller pressure or replace it. Also, check if the wire diameter is non-compatible with the roller or the covering wire guide in the torch is non-compatible.
  • A
    amillerAug 25, 2025
    What to do if there is bad wire feeding with my GYS Welding System?
    • A
      Andrew BushAug 25, 2025
      If you're experiencing bad wire feeding with your GYS Welding System, start by checking the covering wire guide for dirt or damage; clean or replace it if necessary. Also, make sure the drive roller isn't too loose by tightening the drive roller knob. Finally, check if the reel brake is too tight and release the brake.

GYS EASYMIG 110 Specifications

General IconGeneral
Input Voltage230 V
Welding ProcessMIG/MAG
Max Output Current110 A
Welding Current Range30 - 110 A
Wire Diameter0.6 - 0.8 mm
Steel Wire Spool Diameter100 mm
Rated Input Current13 A
No-Load Voltage50 V
Protection ClassIP21S

Related product manuals