What to do if the wire-feeder motor doesn’t operate in GYS EASYMIG 130 Welding System?
If the wire-feeder motor isn’t operating, it could be due to: * The reel or roller brake being too tight; release the brake and rollers. * An electrical supply problem; check that the power switch is in the "On" position.
Why is the welding bead porous when using my GYS Welding System?
If the welding bead is porous when using your GYS Welding System, several factors could be at play. Ensure the gas flow rate is adequate, adjusting it to a range of 15 to 20 L / min. Check if the gas bottle is empty and replace it if needed. The gas quality might be unsatisfactory, so consider replacing it. Air flow or wind can also affect the weld, so prevent drafts and protect the welding area. A dirty gas nozzle can cause porosity, so clean or replace it. Make sure you are using suitable wire for MIG-MAG welding. Lastly, a surface to weld in bad condition (rust, etc…) can cause porosity, so clean the metal before welding.
What to do if there is bad wire feeding with my GYS EASYMIG 130 Welding System?
If you're experiencing bad wire feeding with your GYS Welding System, start by checking the covering wire guide for dirt or damage; clean or replace it if necessary. Also, make sure the drive roller isn't too loose by tightening the drive roller knob. Finally, check if the reel brake is too tight and release the brake.
How to troubleshoot inconsistent welding wire speed on a GYS Welding System?
If the welding wire speed is not constant on your GYS Welding System, it could be due to debris blocking the opening; clean out the contact batch or change it and replace the anti-adherence product Ref.041806. Alternatively, the wire might be skidding in the rollers. In this case, control the roller pressure or replace it. Also, check if the wire diameter is non-compatible with the roller or the covering wire guide in the torch is non-compatible.
Why is there no welding current in my GYS EASYMIG 130 Welding System?
If your GYS Welding System has no welding current, there are several things to check. First, ensure there isn't a bad connection to the main supply. Check the mains connection and verify the plug is fed by a 230 V (1PH) power socket. Second, inspect the earth cable for a bad earth connection, checking both the connection and clamp condition. Finally, check if the torch trigger is inoperative; if so, check the torch trigger and replace the torch if needed.
What causes no gas flow at the end of the torch in GYS Welding System?
No gas flow at the torch end might be due to a bad gas connection. Check the gas connection at the welding machine, the gas regulator, and the solenoid valves.
How to fix the welding wire speed if it is not constant in GYS EASYMIG 130 Welding System?
Inconsistent welding wire speed can be due to: * Debris blocking the opening; clean or change the contact batch and replace the anti-adherence product (Ref. 041806). * The wire skidding in the rollers. To resolve this, control or replace the roller, ensure the wire diameter is compatible with the roller, and check that the covering wire guide in the torch is compatible.
What causes the wire to jam after the rollers in my GYS EASYMIG 130?
Wire jamming after the rollers can occur because: * The guide wire sheath is crushed; check the sheath and torch body. * The wire is jammed in the torch; clean or replace it. * There is no capillary tube; check for the presence of a capillary tube. * The wire speed is too fast; reduce the wire speed.
How to fix the welding wire speed if it is not constant in my GYS Welding System?
Inconsistent welding wire speed can be caused by: * Debris blocking the opening; clean out or change the contact batch and replace the anti-adherence product (Ref.041806). * The wire skidding in the rollers. To resolve this: * Control or replace the roller. * Ensure the wire diameter is compatible with the roller. * Verify the covering wire guide in the torch is compatible.
How to troubleshoot bad wire feeding on my GYS Welding System?
If you're experiencing bad wire feeding, consider these possible causes and solutions: * The covering wire guide might be dirty or damaged; clean or replace it. * The drive roller may be too loose; tighten the drive roller knob. * The reel brake might be too tight; release the brake. * There could be a bad connection to the main supply; check the mains connection and ensure the plug is fed by a 230 V (1PH) power socket. * A bad earth connection could be the issue; check the earth cable (connection and clamp condition).
Covers basic safety recommendations, environment, and personal protective equipment.
Addresses fumes, gas, fire risks, gas bottle safety, and electrical safety precautions.
Details CEM classification, interference, and welding area assessment for EMC.
Guidance on equipment installation, product overview, and maintenance recommendations.
Explanation of the settings panel, assembly, and gas coupling procedures.
Lists symptoms, causes, and remedies for common welding problems.
General| Input Voltage | 230 V |
|---|---|
| Max Output Current | 130 A |
| Welding Process | MIG/MAG |
| Welding Current | 30 - 130 A |
| Wire Diameter | 0.6 - 0.8 mm |
| Steel wire spool diameter | 200 mm |
| Protection index | IP21S |
| Rated Input Current | 16 A |
To Next Page
