To Next PageTo Next PageWhat to do if the wire jams (after the rollers) on my GYS Welding System?
If the wire is jamming after the rollers, check the following: * The guide wire sheath might be crushed; inspect the sheath and torch body. * The wire could be jammed in the torch; clean or replace it. * There might be no capillary tube; check for the presence of a capillary tube. * The wire speed may be too fast; reduce the wire speed.
Why is the welding bead porous when using my GYS Welding System?
If the welding bead is porous when using your GYS Welding System, several factors could be at play. Ensure the gas flow rate is adequate, adjusting it to a range of 15 to 20 L / min. Check if the gas bottle is empty and replace it if needed. The gas quality might be unsatisfactory, so consider replacing it. Air flow or wind can also affect the weld, so prevent drafts and protect the welding area. A dirty gas nozzle can cause porosity, so clean or replace it. Make sure you are using suitable wire for MIG-MAG welding. Lastly, a surface to weld in bad condition (rust, etc…) can cause porosity, so clean the metal before welding.
What to do if there is bad wire feeding with my GYS EASYMIG 130 Welding System?
If you're experiencing bad wire feeding with your GYS Welding System, start by checking the covering wire guide for dirt or damage; clean or replace it if necessary. Also, make sure the drive roller isn't too loose by tightening the drive roller knob. Finally, check if the reel brake is too tight and release the brake.
How to troubleshoot inconsistent welding wire speed on a GYS Welding System?
If the welding wire speed is not constant on your GYS Welding System, it could be due to debris blocking the opening; clean out the contact batch or change it and replace the anti-adherence product Ref.041806. Alternatively, the wire might be skidding in the rollers. In this case, control the roller pressure or replace it. Also, check if the wire diameter is non-compatible with the roller or the covering wire guide in the torch is non-compatible.
Why is there no welding current in my GYS EASYMIG 130 Welding System?
If your GYS Welding System has no welding current, there are several things to check. First, ensure there isn't a bad connection to the main supply. Check the mains connection and verify the plug is fed by a 230 V (1PH) power socket. Second, inspect the earth cable for a bad earth connection, checking both the connection and clamp condition. Finally, check if the torch trigger is inoperative; if so, check the torch trigger and replace the torch if needed.
What causes wire jams after the rollers in a GYS EASYMIG 130?
If the wire jams after the rollers in your GYS Welding System, start by checking the sheath and torch body for a crushed guide wire sheath. Also, check for wire jammed in the torch, clean or replace if necessary. Ensure the presence of a capillary tube. If the wire speed is too fast, reduce the wire speed.
What causes bad wire feeding in a GYS Welding System?
Bad wire feeding can be caused by several factors: * A dirty or damaged covering wire guide; clean or replace it. * The drive roller being too loose; tighten the drive roller knob. * The reel brake being too tight; release the brake. * A bad connection to the main supply; check the mains connection and ensure the plug is fed by a 230 V (1PH) power socket. * A bad earth connection; check the earth cable (connection and clamp condition).
Why is there no gas flow at the end of the torch of my GYS Welding System?
A lack of gas flow at the torch end may be due to a bad gas connection. Check the gas connection at the welding machine, as well as the gas regulator and the solenoid valves.
How to fix the welding wire speed if it is not constant in my GYS Welding System?
Inconsistent welding wire speed can be caused by: * Debris blocking the opening; clean out or change the contact batch and replace the anti-adherence product (Ref.041806). * The wire skidding in the rollers. To resolve this: * Control or replace the roller. * Ensure the wire diameter is compatible with the roller. * Verify the covering wire guide in the torch is compatible.
How to troubleshoot bad wire feeding on my GYS Welding System?
If you're experiencing bad wire feeding, consider these possible causes and solutions: * The covering wire guide might be dirty or damaged; clean or replace it. * The drive roller may be too loose; tighten the drive roller knob. * The reel brake might be too tight; release the brake. * There could be a bad connection to the main supply; check the mains connection and ensure the plug is fed by a 230 V (1PH) power socket. * A bad earth connection could be the issue; check the earth cable (connection and clamp condition).
General| Input Voltage | 230 V |
|---|---|
| Max Output Current | 130 A |
| Welding Process | MIG/MAG |
| Welding Current | 30 - 130 A |
| Wire Diameter | 0.6 - 0.8 mm |
| Steel wire spool diameter | 200 mm |
| Protection index | IP21S |
| Rated Input Current | 16 A |
