To Next PageTo Next PageWhy is there no gas flow at the end of the torch on my GYS EASYMIG 130?
If there is no gas flow at the end of the torch of your GYS Welding System, it could be due to a bad gas connection. Check the gas connection at the welding machine, the gas regulator, and the solenoid valves.
Why doesn't the wire-feeder motor operate on my GYS EASYMIG 130?
If the wire-feeder motor doesn’t operate on your GYS Welding System, it could be due to a reel or roller brake being too tight. Release the brake and rollers. Another potential cause is an electrical supply problem. Check that the power switch is in the "On" position.
What causes wire jams after the rollers in a GYS EASYMIG 130?
If the wire jams after the rollers in your GYS Welding System, start by checking the sheath and torch body for a crushed guide wire sheath. Also, check for wire jammed in the torch, clean or replace if necessary. Ensure the presence of a capillary tube. If the wire speed is too fast, reduce the wire speed.
Why is there no welding current in my GYS EASYMIG 130 Welding System?
If your GYS Welding System has no welding current, there are several things to check. First, ensure there isn't a bad connection to the main supply. Check the mains connection and verify the plug is fed by a 230 V (1PH) power socket. Second, inspect the earth cable for a bad earth connection, checking both the connection and clamp condition. Finally, check if the torch trigger is inoperative; if so, check the torch trigger and replace the torch if needed.
How to troubleshoot inconsistent welding wire speed on a GYS Welding System?
If the welding wire speed is not constant on your GYS Welding System, it could be due to debris blocking the opening; clean out the contact batch or change it and replace the anti-adherence product Ref.041806. Alternatively, the wire might be skidding in the rollers. In this case, control the roller pressure or replace it. Also, check if the wire diameter is non-compatible with the roller or the covering wire guide in the torch is non-compatible.
What to do if there is bad wire feeding with my GYS EASYMIG 130 Welding System?
If you're experiencing bad wire feeding with your GYS Welding System, start by checking the covering wire guide for dirt or damage; clean or replace it if necessary. Also, make sure the drive roller isn't too loose by tightening the drive roller knob. Finally, check if the reel brake is too tight and release the brake.
Why is the welding bead porous when using my GYS Welding System?
If the welding bead is porous when using your GYS Welding System, several factors could be at play. Ensure the gas flow rate is adequate, adjusting it to a range of 15 to 20 L / min. Check if the gas bottle is empty and replace it if needed. The gas quality might be unsatisfactory, so consider replacing it. Air flow or wind can also affect the weld, so prevent drafts and protect the welding area. A dirty gas nozzle can cause porosity, so clean or replace it. Make sure you are using suitable wire for MIG-MAG welding. Lastly, a surface to weld in bad condition (rust, etc…) can cause porosity, so clean the metal before welding.
General| Input Voltage | 230 V |
|---|---|
| Max Output Current | 130 A |
| Welding Process | MIG/MAG |
| Welding Current | 30 - 130 A |
| Wire Diameter | 0.6 - 0.8 mm |
| Steel wire spool diameter | 200 mm |
| Protection index | IP21S |
| Rated Input Current | 16 A |
Covers basic safety recommendations, environment, and personal protective equipment.
Addresses fumes, gas, fire risks, gas bottle safety, and electrical safety precautions.
Details CEM classification, interference, and welding area assessment for EMC.
Guidance on equipment installation, product overview, and maintenance recommendations.
Explanation of the settings panel, assembly, and gas coupling procedures.
Lists symptoms, causes, and remedies for common welding problems.
