Why does my GYS Remote Starter show 0% in START ENGINE mode and won't start?
If your GYS Remote Starter displays 0% in START ENGINE mode, preventing the start, it's likely because the battery is sulfated. To resolve this, charge the battery fully before attempting to use the START ENGINE mode again. This is a protective measure to safeguard the on-board electronics.
What to do if the battery boils when using GYS Remote Starter?
If the battery boils when using the GYS Remote Starter, it could be due to an incorrect voltage selection (12V or 24V). In this case, charge the battery before attempting to start the engine again. Another reason could be that your battery has elements in short circuit, which means that the battery is unrecoverable and needs to be replaced.
What to do if no LED switches on my GYS Remote Starter?
If no LED switches on your GYS Remote Starter, there could be a major power supply fault, so check your mains power supply. Alternatively, the machine may have overheated, activating the thermal protection («th»). In this case, ventilate the area. Also, make sure that the start/stop button is pressed.
What to do if the error LED switches on and the buzzer sounds on my GYS Battery Charger?
If the error LED is on and the buzzer sounds, several issues could be the cause. First, the clamps may be in short circuit or have reverse polarity, so check that the fuses haven't melted and ensure the clamps are not short-circuited and the polarities are correct. Another reason may be a faulty battery. Use a voltmeter to check the terminals’ voltage. If the voltage jumps to 2.5V per element immediately, the battery might be sulfated or damaged. Also, ensure that the clamps are correctly connected for the voltage (12V or 24V). If the display shows «BAt HS», connect a battery or, if the battery voltage is
Why no LED switches on on my GYS Battery Charger?
If no LED switches on, there could be a major power supply fault, so check your mains power supply. Another reason might be machine overheat, which activates the thermal protection «th», so ventilate the area. Also, ensure the start/stop button is pressed.
What to do if sparks appear at the clamps of my GYS Battery Charger?
Sparks at the clamps can be caused by polarity reversal, so connect the clamps the correct way (+/+;-/-). Sparks may also appear if Timer mode is active.
What to do if my GYS Battery Charger shows 0% in START ENGINE mode and the start is impossible?
If the display shows 0% in START ENGINE mode and starting is impossible, the battery may be sulfated. The machine automatically blocks the start to protect on-board electronics. Charge the battery before attempting a START ENGINE again.
Why is my GYS Battery Charger making the battery boil?
If the battery boils, the voltage selection (12V or 24V) may be incorrect. Also, your battery may have elements in short circuit, which means it cannot be recovered and must be changed.
What to do if desulphation charging time is more than 1 hour on my GYS Battery Charger?
If the desulphation charging time is more than 1 hour, the battery cannot be recovered and should be replaced.
What to do if the error LED switches on in my GYS Remote Starter?
If the error LED switches on your GYS Remote Starter, it could be due to several reasons. First, check your mains power supply. Second, the clamps might be in short circuit or have reversed polarity. In this case, verify that the fuses are intact. Also, ensure the clamps aren't in short circuit and polarities are correct. If you're charging a faulty battery, check its terminals' voltage with a voltmeter; a sudden jump to 2.5V per element indicates sulfation or damage. A voltage error (12-24V) could also be the cause, so confirm the clamps are correctly connected for the appropriate voltage. If the battery isn't connected or reads
Warnings about explosive gas and fire hazards during battery charging.
Precautions for handling battery acid to prevent skin and eye contact.
Procedures for connecting and disconnecting the battery charger safely.
Choosing the appropriate charge speed based on battery capacity.
Procedure for using the device to start a vehicle engine.
Understanding precharge time and start attempt limits.
How to test the vehicle's alternator charge capacity using the device.
Diagnosing issues based on error LED lights and buzzer sounds.
Resolving problems when the vehicle start is impossible.
Addressing issues like battery boiling or sparks at the clamps.
General| Brand | GYS |
|---|---|
| Model | STARTIUM 680E |
| Category | Welding System |
| Language | English |
To Next Page
