What to do if auger in SIA turns in the wrong direction on H&S Farm Equipment?
If the auger in your H&S Farm Equipment's SIA turns in the wrong direction, the motor connections are likely crossed. Switch the hose connections to change the direction of motor rotation.
What to do if the tank unloads slow on my H&S GM 170 Farm Equipment?
If your H&S Farm Equipment's tank unloads too slowly, the issue might be due to insufficient oil flow to the motors. Try increasing the tractor RPM speed. A plugged oil filter can also cause this problem, so replace the filter. Other potential causes include a defective hydraulic pump (replace it), a variable speed control valve that isn't fully open (open it more), a defective hydraulic motor (repair or replace it), oil that is too thin (replace it with heavier oil), or not enough oil flow to the hydraulic pump (change the oil filter, replace the oil, and fill to the proper level). Also, check for and tighten any loose connections to the motor.
How to troubleshoot decreased capacity in H&S GM 170?
Low capacity in your H&S Farm Equipment can occur for several reasons. First, ensure the mill is operating at the recommended RPM speed by adjusting the tractor throttle. If the mill loses speed as material enters it, adjust the Mill/Blower sheave alignment and/or drive belt tension. Also, a worn screen can reduce capacity, so rotate or replace the screen. Lastly, check for and unplug a plugged blower inlet.
Why does the pump squeal during start up on my H&S Farm Equipment?
If your H&S Farm Equipment's pump squeals during start up, it could be due to oil that is too heavy or cold; allow the oil to warm up or switch to a recommended lighter oil. Another possible cause is a low oil level in the reservoir; add oil to bring it between the minimum and maximum indicator levels.
How to reduce excessive dust from H&S GM 170?
If you're experiencing excessive dust with your H&S Farm Equipment, check and unplug the blower inlet. Also, make sure the collector is uncovered while operating.
Why won't the Swinging Intake Auger attachment operate on my H&S GM 170 Farm Equipment?
If the Swinging Intake Auger (SIA) attachment on your H&S Farm Equipment will not operate, first check if the SIA variable speed control is in the off position; check the mechanical linkage controls and open the valve. If that's not the issue, the SIA variable speed control valve relief pressure may be set too low; check the pressure to the valve, and if it's low, adjust it to the factory setting or replace it if it will not adjust.
Why will the discharge auger variable speed control valve not engage or disengage on H&S GM 170 Farm Equipment?
If the discharge auger variable speed control valve on your H&S Farm Equipment will not engage or disengage, the variable speed control valve is likely defective and needs to be replaced.
Why is it difficult to engage or disengage variable speed control valve on H&S Farm Equipment?
If you find it difficult to engage or disengage the variable speed control valve on your H&S Farm Equipment, the valve itself may be defective and require replacement.
What to do if transfer auger doesn’t turn on H&S GM 170 Farm Equipment?
If the transfer auger on your H&S Farm Equipment doesn't turn, check for a sheared transfer auger shear bolt and replace it, correcting the cause of the failure. Also, inspect the front drive chain for breaks or disconnections; repair or replace the chain as needed.
What to do if mixing auger doesn’t turn on H&S GM 170 Farm Equipment?
If your H&S Farm Equipment's mixing auger doesn’t turn, it could be due to a sheared transmission shear bolt; replace the bolt and correct the cause of the bolt failure. Other potential causes include a disconnected front or rear drive chain (repair or replace the chain), a sheared sprocket key or transmission gear key (replace the key), or a broken shaft (replace the shaft).
Form to register the product warranty with the manufacturer.
Details of the manufacturer's warranty policy and terms.
Understanding safety symbols and alerts in the manual and on the machine.
Explains the meaning of DANGER, WARNING, and CAUTION signal words.
Emphasizes reading all safety messages and following procedures.
Details maximum safe towing speed and related risks.
Table of torque specifications for inch-based cap screws.
Table of torque specifications for metric cap screws.
Instructions for installing and inflating wheels and tires.
Information about drain plug placement for storage and operation.
Guidelines for storing the equipment, including water drainage.
Details on safety reflectors and mounting brackets for transport.
Information about optional highway transport lighting kits.
Steps for connecting the PTO and ensuring proper alignment and distances.
Specifies the hydraulic hose connections required for the GM 170.
Pre-operation checks and procedures for the mixer itself.
Procedure for immediate shutdown in emergencies or foreign object entry.
Pre-operation checks, lubrication, and initial setup steps.
Mixing tank capacity, HP requirements, and PTO drive options.
How the mill cylinder grinds material and its path.
Overview of hydraulic systems, relief valves, and pump/motor drives.
Discharge auger system, needle valves, and intake operations.
Operation of hydraulic attachments, gravity feeder, and magnets.
Screen selection, supplement hopper, and tank lid operation.
Overload protection, unplugging, and overfeeding resolution.
Clearing blower blockages and resolving drive belt slippage.
Main shear bolt procedures and blockage resolution.
Aligning sheaves and adjusting drive belt tension for mill/blower.
Adjusting front and rear drive chain tensions.
Adjusting SIA brake tension and counterbalance spring tension.
Adjusting mill screen cover latches, needle valves, and tank lid.
Maintaining hydraulic pump sheaves, belt tension, and reservoir.
Procedures for replacing the mill/blower drive belt.
Replacing main drive shaft bearings and checking the engaging pin.
Rotating/replacing mill hammers and adjusting the mill throat plate.
Servicing the mixing auger/tube and replacing the main shear bolt.
Removing transmission and clearing unloading auger blockages.
Details on 3' and 6' folding auger extensions and cradle extension.
Information on optional Digi-Star EZ 2400 and EZ 3400 scales.
Available screen sizes and optional transport lighting kits.
Importance of lubrication and proper fluid disposal.
Checking transmission oil level and filling the cyclonic reservoir.
Specific locations and intervals for greasing various fittings.
Procedures for lubricating and servicing wheel bearings.
Common issues with the drive system, causes, and remedies.
Troubleshooting low capacity, vibration, dust, and grinding size.
Resolving tank unloading and hydraulic system malfunctions.
Diagnosing issues with augers, pumps, motors, and relief valves.
H&S commitment to product improvement and right to make changes.
General| Brand | H&S |
|---|---|
| Model | GM 170 |
| Category | Farm Equipment |
| Language | English |
To Next Page
