EasyManuals Logo

Harman Kardon AVR 2700 Owner's Manual

Harman Kardon AVR 2700
63 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #18 background imageLoading...
Page #18 background image
18
AVR
Making Connections
C
onnect Your Audio and Video Source Device
s
Source devices are components where a playback signal originates, e.g. a Blu-ray
Disc™ or DVD player; a cable, satellite or HDTV tuner; etc. Your AVR has several different
t
ypes of input connectors for your audio and video source devices: HDMI, component
vid
eo, compos
i
te v
id
eo, opt
i
ca
l
di
g
i
ta
l
au
di
o, coax
i
a
l
di
g
i
ta
l
au
di
o an
d
ana
l
og au
di
o.
he connectors are not labeled for specific types of source devices; they are labeled
n
umer
i
ca
ll
y, so you can connect your
d
ev
i
ces accor
di
ng to your
i
n
di
v
id
ua
l
system
s
m
a
k
e-up.
Your AVR’s various source buttons have default assi
g
nments to different input connectors
(
listed in the “Default
C
onnector
(
s
)
column of the table below
)
. For ease of setup, you
should connect each source device to the connector where the correspondin
g
default
source button is assi
g
ned
(
e.
g
., connect your Blu-ray Disc player to HDMI 1
)
.
However, you can connect your source devices as you wish and re-assign any of the
input connections to any of the
S
ource Buttons listed in the table according to where you
a
ctuall
y
connect each of
y
our source devices.
A
s you connect your various source devices, fill out the “Connected Component” column
in the table – it will make it easier
f
or you to assi
g
n the various source buttons a
f
ter
ou have completed makin
all o
the connections.
You will make any chan
es to the
source-button assi
g
nments and fill in the “Assi
g
ned Connector
(
s
)
column later in the
setup process.
)
Note: You cannot assign connectors to the Network, Radio and USB source buttons
.
Source Button Default Connector(s) Assigned Connector(s) Connected Device
Disc HDMI 1
Cable/Sat HDMI 2
Game HDMI 3
Media Server HDMI 4
DVR HDMI 5
TV None/Optical Digital Audio 1
Aux HDMI Front
A (red) HDMI 6
B (green) HDMI 7
C (yellow) Composite Video 1/Analog Audio 1
D (blue) Composite Video 2/Analog Audio 2
Monitor Output Connector Connected Device
HDMI Out 1
HDMI Out 2
(AVR 3700/AVR 370 only)
Composite Video Monitor Out
Record Output Connector Connected Device
Analog Audio Rec Out
Source Buttons and Assigned Connectors

Table of Contents

Other manuals for Harman Kardon AVR 2700

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Harman Kardon AVR 2700 and is the answer not in the manual?

Harman Kardon AVR 2700 Specifications

Audio Section IconAudio Section
stereo mode continuous average power100 watts/ch, 20Hz – 20kHz, <0.07% THD, both channels driven @ 8 ohms, 6-ohm certified
multichannel power100 watts/ch, 20Hz – 20kHz, <0.07% THD, two channels driven @ 8 ohms, 6-ohm certified
bandwidth @ 1W (+0dB/–3dB)10Hz – 130kHz
input sensitivity/impedance (line-in)200mV/47k ohms
signal-to-noise ratio (IHF-A)100dB
high instantaneous current capability (HCC)±35 amps
slew rate40V/μsec
FM Tuner Section IconFM Tuner Section
frequency range87.5MHz–108.0MHz
usable sensitivity (IHF)1.3μV/13.2dBf
signal-to-noise ratio (mono/stereo)70dB/68dB
distortion (mono/stereo)0.2%/0.3%
stereo separation40dB @ 1kHz
selectivity (±400kHz)70dB
image rejection80dB
IF rejection90dB
AM Tuner Section IconAM Tuner Section
frequency range520kHz – 1, 720kHz
signal-to-noise ratio45dB
usable sensitivity (loop)500μV
distortion (1kHz)50%, mod 0.8%
selectivity (±10kHz)30dB
Video Section IconVideo Section
television formatNTSC
input level/impedance1Vp-p/75 ohms
output level/impedance1Vp-p/75 ohms
video frequency response (composite video)10Hz – 8MHz (–3dB)
General IconGeneral
power requirementAC 120V/60Hz
power consumption120W idle; 1405W maximum
dimensions (W x H x D)17-5/16" x 6-1/2" x 15" (440mm x 165mm x 382mm)
weight7.7kg (16.9 lb)

Related product manuals