EasyManuals Logo

Harman Kardon AVR 2700 Owner's Manual

Harman Kardon AVR 2700
63 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #23 background imageLoading...
Page #23 background image
23
ENGLISH
AVR
Making Connections,
To control more than one source device through the AVR’s IR Remote Out connector,
connect all sources in “daisy chain” fashion, connecting each device’s IR output to the
next device’s IR input, starting with the AVR.
s If you install a multizone system, connect an IR control device to the Zone 2 IR In
connector for remote-room control of the multizone system, source devices and
volume in the remote zone.
External IR Receiver
Zone 2
Main Room
Zone 2 Speakers
AVR
If a source device is shared with the main listening area, any control commands issued
to that source will also affect the main room.
Connect the Trigger Output
If your system has equipment that can be controlled by a DC trigger signal, connect it to
the AVR’s Trigger Out connector with a mono 1/8-inch (3.5mm) mini-plug interconnect
cable. The AVR will supply a 12V DC (100mA) trigger signal at this connection whenever
it is powered on.
AVR
Device with
Trigger In Connector
Mono 1/8-inch
(3.5mm) Mini-Plug
Interconnect
(not supplied)
Connect to AC Power
Connect the supplied AC power cord to the AVR’s AC Input connector and then to a
working AC power outlet.
AC Power
Outlet
AVR
AC Input
Connector
Power Cord (supplied)

Table of Contents

Other manuals for Harman Kardon AVR 2700

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Harman Kardon AVR 2700 and is the answer not in the manual?

Harman Kardon AVR 2700 Specifications

Audio Section IconAudio Section
stereo mode continuous average power100 watts/ch, 20Hz – 20kHz, <0.07% THD, both channels driven @ 8 ohms, 6-ohm certified
multichannel power100 watts/ch, 20Hz – 20kHz, <0.07% THD, two channels driven @ 8 ohms, 6-ohm certified
bandwidth @ 1W (+0dB/–3dB)10Hz – 130kHz
input sensitivity/impedance (line-in)200mV/47k ohms
signal-to-noise ratio (IHF-A)100dB
high instantaneous current capability (HCC)±35 amps
slew rate40V/μsec
FM Tuner Section IconFM Tuner Section
frequency range87.5MHz–108.0MHz
usable sensitivity (IHF)1.3μV/13.2dBf
signal-to-noise ratio (mono/stereo)70dB/68dB
distortion (mono/stereo)0.2%/0.3%
stereo separation40dB @ 1kHz
selectivity (±400kHz)70dB
image rejection80dB
IF rejection90dB
AM Tuner Section IconAM Tuner Section
frequency range520kHz – 1, 720kHz
signal-to-noise ratio45dB
usable sensitivity (loop)500μV
distortion (1kHz)50%, mod 0.8%
selectivity (±10kHz)30dB
Video Section IconVideo Section
television formatNTSC
input level/impedance1Vp-p/75 ohms
output level/impedance1Vp-p/75 ohms
video frequency response (composite video)10Hz – 8MHz (–3dB)
General IconGeneral
power requirementAC 120V/60Hz
power consumption120W idle; 1405W maximum
dimensions (W x H x D)17-5/16" x 6-1/2" x 15" (440mm x 165mm x 382mm)
weight7.7kg (16.9 lb)

Related product manuals