(
CONTROLS AND FUNCTIONS
Front
Panel
harman/kardon
AVRBO
m
[Ill':':.~!
D Information display: This dis-
play delivers messages and status
indications to help you operate the
receiver. Refer to the separate dia-
gram for a complete explanation of
the FL display.
l!I Remote Sensor Window: The
sensor behind this window receives
infrared signals from the remote con-
trol. Aim the remote at this area and
do
not block or cover it unless an
external remote sensor is installed.
ID
AM/FM Tuner Mode Selection:
Press this button once to select the
tuner. Press it again to switch
between FM, MW and
LW.
El
CD: Press this button to select
the CD player.
(;I
Tape1/Monltor: Press this button
to select Tape One as the input
source. A red LED above the button
will illuminate to indicate that the
Tape Monitor has been selected.
DJ
Tape 2: Press this button to select
Tape
2.
61
Video Sources: Press any of
these buttons to select a video input
source.
EJ
Aux: Press this button to select
the source connected to the front
panel Aux jacks.
m Multlroom Audio Select: Press
this button to turn on the feed to the
remote zone. The remote zone will
stay on after the main power switch
is turned off until it is switched off by
the remote room control or
by
press-
ing this button again.
ml
Display: Press this button to
turn off the front panel FL display.
The
DISP indicator will illuminate
to remind you that the unit is still
turned on.
m OSD (On Screen Display):
Press the button briefly to display a
system status report on your video
screen. Press and hold the button to
change the video standard.
&m
Delay: Press this button to
increase the delay to the rear (sur-
round) channels.
ml
Mode: Press these buttons to
scroll
up
.A.
or down T through the
list
of
available surround modes.
G)ONLY
mJ
P-Set: Press these buttons to
manually scroll
up
.A.
or down T
through the stations programmed
into the receiver's preset memory.
ml
P-Scan: Press this button to
automatically scan through the
FM
or AM stations preset into the receiv-
er's memory. Press the button again
to stop the scan when the tuner
is
at
the desired station.
ml
Tune: Press these buttons to
manually scan up
.A.
or down T
through the
FM,
LW
or AM bands.
(6
Mute: Press this button to
cut
the
output to the speakers. Press it
again to return to the previous vol-
ume level.
ml
Volume Control:
Turn
the knob
clockwise to increase volume, coun-
terclockwise to decrease the vol-
ume. Note that approximately two
revolutions of the knob are required
to
go
from no output to maximum
volume.
ml
Power: press this button
once
to
turn the
unit
on
or
off. In
order
to
use
the remote control to
turn
the
unit
on
the
power
switch
must
be
pressed
once,
and
then the unit
must
be
turned
off
via the remote.
The
LED
indicator
light
surrounding
the
power
switch will
glow
amber
when the
unit
is
in the Standby
mode
and
green
when
the
unit
is on.
f.m
Headphone Jack: Plug standard
stereo headphones into this jack for
private listening.
NOTE: When the headphones are
in
use the output to the speakers is
muted and the surround mode is
automatically switched to
STEREO.
When the headphones are removed
from the jack, sound to the speakers
is restored and the unit returns to the
previous sound mode.
11)
6 Channel Direct: Press this but-
ton to select the output of an exter-
nal multichannel audio adapter.
fE
Tape 1 Copy: Press this button to
select the input for the recorder con-
nected to Tape
1.
The first press will
select the source currently being lis-
tened to. Press again to select the
input
in
the following order:
Tuner
➔
CD
➔
Tape
2
➔
Source.
fJl
VCR 1 Copy: Press this button
to select the input to the recorder
connected to
VCR
1.
The first
press selects the input currently
being viewed. Press the button
again to select the input
in
the
following order:
TV
➔
LD
➔
VCR2
➔
AUX
➔ Source
f:E
Memo: The memo button is used
to enter stations to the tuner's preset
memory
in
either the manual or auto-
matic modes. It is also used
in
clear-
ing the memory and entering the
sleep timer period.
f1ll
Clear: The clear button
is
used
to cancel tuning, memory input or
when clearing the unit's memories.
f1!I
FM Mode: Press this button
to select the tuning mode for
FM
stations.
PB
RDS Display: When a station
transmitting
RDS
data is tuned,
press this button to view the tuning
frequency.
P.m
RDS AF: The button is used to
search for stations transmitting a
specific programme type that offers
better reception than the currently
tuned station.
fE
RDS PTY: Press this button to
view the programme type (PTY)
when an
RDS
station is tuned. It is
also used to initiate a search for
RDS
stations transmitting a specific pro-
gramme type.
8I!]
Bass: This knob adjusts the tone
of low frequency sounds. Turn it to
the right to boost bass frequencies
or to the left to cut bass frequencies.
&JI
Treble: This knob adjusts
the tone of high frequency sounds.
Turn it to the right to boost high
frequencies·or to the left to cut high
frequencies.
IE Balance: This knob adjusts the
balance between the front left and
right speakers.
~
Front Panel Inputs: Audio or
Video sources connected to these
jacks may
be
selected by pressing
the Aux button
El
€t
[
◄
ONLY
◄
0
Use/L
the opera
control.
SI
operation
theremot,
f)
Main
buttons
tc
osourc
of these t
source
th;
through tt
is selecte
and
nume
also trans
to control
C,Sourc
tons to cc
source
de
C,Surrc
Press
one
a surroun
tening
se:
0Maln
control
th,
all chanrn
neously.
To Next Page
Loading...
