Why HATO Garage Door Opener remote control does not work?
The remote control may not be working due to a discharged battery, so replace the battery. Alternatively, the remote control may not be logged into the drive, so log it in according to the instructions. If neither of these solutions work, the remote control may be faulty.
What to do if HATO 200 when closing, the gate stops suddenly and moves backwards?
This issue may occur due to increased resistance to door sliding. Unblock the drive and manually move the gate to check if it moves easily and is well-balanced with springs. It can also happen because of insufficient drive force; in this case, set the correct drive force in accordance with the instructions and standards.
What to do if HATO 200 door opens but does not close?
If the door opens but does not close, the photocells support function may be enabled without photocells installed; disable the photocell operation function according to the instructions. Another cause may be that the path of infrared rays has been interrupted; remove the obstacle. Faulty photocells can also be the cause; if so, send the photocells to the service together with a description of the fault and the purchase document. Finally, insufficient drive force can cause this problem; set the correct drive force.
Why HATO Garage Door Opener range of the remote control is too small?
The range of the remote control might be too small because the drive is located in a steel or reinforced concrete garage, requiring the installation of an external antenna by a specialist. Another reason could be a low battery, so try battery replacement. The remote control or the radio module in the drive could also be faulty.
What to do if HATO 200 actuator is inoperative after programming the end position?
The actuator may be inoperative after programming the end position if the end positions were incorrectly set (LED displays "-"). Re-program the end positions, ensuring the top position is set first, followed by the bottom position, and that neither position is set to pressure. Also, the gate lock function may have been activated (the display shows "||" but the drive does not work). If this was accidental, turn the function off. If intentional, first press button "3" on the remote control and then the logged-in button. Finally, the remote control button for the drive may not be logged in; log it in according to the instructions.
What to do if HATO Garage Door Opener nothing is displayed on the LED display?
If nothing is displayed on the LED display and the gate is down, it could be due to no power. Make sure the power is on. It could also be due to a blown fuse. Check the fuse and, if necessary, replace it with a new one (2.5A).
What to do if HATO Garage Door Opener after a power failure and restarting, the drive automatically moves the gate?
If, after a power failure and restart, the drive automatically moves the gate, it could be due to the wrong type of wall switch controlling the door. To control the gate with a wall button, a "bell" type button with normally open contacts should be used. Replace the button with the correct one. It could also be a defective microcontroller.
What to do if HATO Garage Door Opener selected button on the remote control cannot be logged in?
If the selected button on the remote control cannot be logged in, it may be because the selected button is used for the lock function. Select a different button for logging in. Alternatively, the remote control may be defective.
What does it mean when the sign appeared on the HATO Garage Door Opener LED display?
If the sign appeared on the LED display, it means that the photocells support function is enabled, but no photocells are connected. Connect the photocells or disable the photocell support function.
What to do if HATO Garage Door Opener when closing the door, the drive does not react to the obstacle in the light of the photocells?
If the drive does not react to an obstacle in the light of the photocells when closing the door, it indicates incorrect photocells. If the gate is open and the photocells are covered, the gate will not close, and if the gate does not respond to an obstacle, it means that the photocells are not compatible with the drive. Suitable photocells for the HATO 200 model must be used.
Defines the primary intended use of the sectional door drive.
Provides essential safety and operational guidelines for users.
Details the features, functions, and components of the garage door drive system.
Lists key technical data, including power, speed, and environmental operating conditions.
Presents physical size measurements and lists all parts provided with the automation kit.
Guides through the step-by-step process of physically installing the drive unit.
Explains control buttons, external connectors, wiring, and verification of assembly correctness.
Details setting open/close limits and adjusting overload sensor sensitivity.
Covers installation of photocells and configuration of auto-closing function.
Explains programming remotes and activating the gate lock security.
Lists essential checks and verifications required after installation and programming.
General| Model | HATO 200 |
|---|---|
| Category | Garage Door Opener |
| Battery Backup | No |
| Warranty | 2 years |
| Motor Type | DC Motor |
| Remote Control | Yes |
To Next Page
