To Next PageTo Next PageHow to turn on Healthrider 875p?
To ensure your Healthrider Treadmill powers on, first, check that the power cord is correctly plugged into a properly earthed outlet. Next, confirm the key is fully inserted into the console. Also, inspect the circuit breaker located near the power cord; if it protrudes, wait five minutes, then press it back in to reset it. Finally, verify that the on/off switch near the power cord is in the 'on' position.
How to recalibrate incline on Healthrider Treadmill?
To recalibrate the incline on your Healthrider Treadmill, insert the key into the console and press one of the Incline buttons. While the incline is changing, remove the key. After a few seconds, reinsert the key. The treadmill will automatically rise to the maximum incline level and then return to the minimum level, completing the recalibration.
How to fix Healthrider 875p Treadmill speed display?
If the speed display on the console of your Healthrider Treadmill isn't working correctly, remove the key and unplug the power cord. Locate the Reed Switch and the Magnet on the left side of the Pulley. Turn the Pulley until the Magnet is aligned with the Reed Switch, and make sure the Screw is retightened. Reattach the hood, and run the treadmill for a few minutes to check for a correct speed reading.
What to do if Healthrider 875p Treadmill turns off during use?
If your Healthrider Treadmill turns off during use, start by checking the circuit breaker located near the power cord. Ensure the power cord is securely plugged in; if it is, unplug it, wait five minutes, and plug it back in. Also, remove and reinsert the key fully into the console, and verify the on/off switch is in the 'on' position.
Why does the Healthrider 875p Treadmill walking belt slow down when walked on?
To address a walking belt that slows down when walked on your Healthrider Treadmill, begin by removing the key and unplugging the power cord. If the walking belt is overtightened, use the hex key to turn both rear roller adjustment bolts counterclockwise by 1/4 of a turn. When the walking belt is properly tightened, you should be able to lift each side of the walking belt 7–10 cm (3–4 in.) off the walking platform. Plug in the power cord, insert the key, and run the treadmill for a few minutes. Repeat until the walking belt is properly tightened.
What to do if Healthrider Treadmill walking belt is off-centre?
If the walking belt on your Healthrider Treadmill is off-centre or slips when walked on, first remove the key and unplug the power cord. If the belt has shifted left, turn the left rear roller bolt clockwise 1/2 turn with a hex key; if it has shifted right, turn the bolt counterclockwise 1/2 turn. When correctly tightened, you should be able to lift each side of the belt 7–10 cm (3–4 in.) off the walking platform. Plug the cord back in, insert the key, and carefully walk on the treadmill for a few minutes. Repeat until the belt is properly tightened.
How to fix Healthrider 875p chest pulse sensor?
If the chest pulse sensor on your Healthrider Treadmill isn't working correctly, the battery may need to be changed. Locate the battery cover on the back of the sensor unit. Insert a coin into the slot in the cover and turn the cover counterclockwise to the “open” position. Remove the old battery and insert a new CR 2032 battery, making sure that the writing is on top. Ensure the rubber gasket is in place, then replace the battery cover and turn it to the closed position.
General| Brand | Healthrider |
|---|---|
| Model | 875p Treadmill |
| Category | Treadmill |
| Language | English |
Recommendations for clothing, footwear, and wearing safety clips.
Proper power cord connection, fuse replacement, and extension cord use.
Instructions for starting, stopping, speed adjustments, and unattended operation.
Procedure for plugging in the power cord and safety warnings.
Steps to turn on the treadmill and use the safety clip.
How to start the walking belt and change speed settings.
Procedure for modifying the treadmill's incline level.
Steps to choose and initiate a workout program.
How the console indicates progress through program segments.
Steps for using iFIT.com CDs and videocassettes.
Instructions for running iFIT.com programs directly from the website.
Steps to safely fold the treadmill into its storage position.
Procedure for tilting and moving the treadmill using its wheels.
Steps to safely unfold the treadmill and prepare it for use.
