EasyManua.ls Logo

Heath Zenith Motion Sensor Light Control 5408 / 5410 - User Manual

Heath Zenith Motion Sensor Light Control 5408 / 5410
20 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
© 2007 HeathCo LLC 598-1303-01
Motion Sensor Light
Control
Models 5408 / 5410
Features
• Turns on lighting when motion is detected.
• Automatically turns lighting off.
•
Photocell keeps the lighting off during daylight hours.
• 5410 models have Flash Alert feature (light flashes on
then off twice before turning on full brightness).
Requirements
• The light control requires 120-volts AC.
• If you want to use Manual Mode, the control must be
wired through a switch.
• Some codes require installation by a qualified
electrician.
• This product is intended for use with a junction box
marked for use in wet locations.
• The backplate has knockouts so the sensor can be
mounted on most junction boxes.
• In some applications a universal adaptor plate may
be needed. Adaptors are available at home centers
and electrical supply stores.
Cover
Plate
Light Control
Lamp Holders
Sensor
2 Wire
Connectors
Gasket
4 Mounting
Screws (2 sizes)
This package includes:
OPERATION
* resets to Auto Mode at dawn.
Note: When first turned on wait about 1
1
/
2
minutes for
the circuitry to calibrate.
MANUAL MODE
ON-TIME
10 5 1 TEST
10 5 1 TEST
ON-TIME
TEST
... back on.
AUTO
1 Second
OFF then...
Put the ON-TIME switch in the 1, 5,
or 10 minute position.
Put the ON-TIME switch on the bottom
of the sensor in the TEST position.
Manual mode only works at night
because daylight returns the sensor
to AUTO.
Flip the light switch off for one second
then back on to toggle between AUTO
and MANUAL MODE.
Manual mode works only with the
ON-TIME switch in the 1, 5, or 10
position.
Move ON-TIME Switch to
1, 5, or 10 minutes
Mode Switching Summary
Flip light switch off
for one second then
back on*
MANUAL MODE
AUTO
TEST
* If you get confused while switching modes, turn the
power off for one minute, then back on. After the cali-
bration time the control will be in the AUTO mode.
As an ENERGY STAR
®
Partner, Heath
®
/Zenith
has determined that this product meets the EN-
ERGY STAR
®
guidelines for energy efficiency.
This product is ENERGY STAR
®
compliant
when used with 120 Watt bulbs.
Mode: On-Time Works: Day Night
Test
5 Seconds x x
Auto
1, 5, or 10 Min x
Manual
Until Dawn* x

Table of Contents

Questions and Answers

  • M
    Michael PerryJul 30, 2025
    How to fix Heath Zenith Home Safety Product lights that won't come on?
    • B
      barajasjoshuaJul 30, 2025
      If your Heath Zenith Home Safety Product lights won't turn on, several factors could be at play. First, make sure the light switch is on. If that's not the issue, check if the flood light is either loose or burned out, and secure or replace it as needed. Also, verify that a fuse hasn't blown or a circuit breaker hasn't tripped; replace the fuse or reset the breaker if necessary. Ensure that the daylight turn-off feature isn't active by re-checking after dark. If it's a new installation, inspect the circuit wiring for any errors. Finally, try re-aiming the sensor to ensure it covers the desired area.
  • A
    April SheaAug 5, 2025
    Why do my Heath Zenith Home Safety Product lights stay on all the time?
    • H
      henrylittleAug 5, 2025
      If the lights on your Heath Zenith Home Safety Product are staying on continuously, it might be due to a few reasons. Check if a flood lamp is too close to the sensor or pointed at objects that reflect heat, and if so, reposition the lamp. Also, verify that the light control isn't directed towards a heat source, such as an air vent or heat-reflective surface; if it is, reposition the sensor. Lastly, make sure the light control is not in Manual Mode; switch it to Auto.
  • S
    Sharon HarrisAug 11, 2025
    What to do if Heath Zenith Home Safety Product lights come on for no reason?
    • A
      amandashawAug 11, 2025
      If your Heath Zenith Home Safety Product lights are activating for no obvious reason, it could be that the light control is detecting small animals or automobile traffic; in this case, try re-aiming the sensor. Alternatively, the sensitivity might be set too high, so try reducing it.
  • F
    Frank HarrellAug 17, 2025
    Why are my Heath Zenith Home Safety Product lights flashing on and off?
    • K
      kimberly46Aug 17, 2025
      If the lights on your Heath Zenith Home Safety Product are flashing on and off, it could be due to several reasons. Heat or light from the lamps might be triggering the light control, so try repositioning the lamps away from the sensor. Reflected heat from other objects could also be affecting the sensor, so reposition the sensor. If the light control is in Test mode, this flashing is normal during warm-up. Light leakage through the flood lamp reflectors might also be the cause, so consider replacing the lamps with new, high-quality PAR 38 lamps. Finally, the light might be in Flash Alert mode, which is normal operation.
  • J
    James KellerAug 23, 2025
    How to stop Heath Zenith Home Safety Product lights from turning on in daylight?
    • A
      Andrea CarterAug 23, 2025
      If your Heath Zenith Home Safety Product lights are turning on during the day, it could be because the light control is installed in a relatively dark location, so try reinstalling it in a darker spot. It's also possible the light control is in Test mode; if so, set the control switch to an ON-TIME position.

Summary

Operation Modes

Test Mode

Set ON-TIME switch to TEST for initial setup and calibration.

Auto Mode

Set ON-TIME switch for 1, 5, or 10 minute auto shut-off.

Manual Mode

Use manual mode for night-time operation, toggled via wall switch.

Mode Switching Summary

Summary of how to switch between TEST, AUTO, and MANUAL modes.

Product Features

Installation Requirements

Installation Guide

Wiring the Light Control

Step-by-step guide for connecting wires, routing, and securing the unit.

Mounting Types

Details on Eave Mount and Wall Mount installation procedures.

Flash Alert Deactivation

Testing and Adjustment

Sensor Controls Overview

Locating and understanding the ON-TIME and SENSITIVITY adjustment dials.

Mounting and Sealing

Securing the light control unit and applying sealant for weatherproofing.

Sensor Aiming Guidelines

Product Specifications

Troubleshooting Common Issues

Customer Support Information

Two Year Limited Warranty

Heath Zenith Motion Sensor Light Control 5408 / 5410 Specifications

General IconGeneral
BrandHeath Zenith
ModelMotion Sensor Light Control 5408 / 5410
CategoryHome Safety Product
LanguageEnglish

Related product manuals