Helmer PC100i - Service Manual

104 pages

Save Page as PDF

To Next Page

360096-1/P

Platelet Incubator Service Manual

i.Series

and Horizon Series™

Countertop

i.Series

PC100i, PC900i, PC1200i

PC100h, PC900h, PC1200h

Floor

i.Series

PC2200i, PC3200i, PC4200i

PC2200h, PC3200h, PC4200h

Main Page

Default Chapter3
- Table of Contents3
1 About this Manual6
- Safety Precautions and Symbols6
- Product Labels7
- Control System8
- Temperature Probes8
- Chart Recorder9
I.series ® Models10
2 Installation and Configuration10
- Install Batteries for Backup Power10
- Platelet Agitator and Platelet Incubator Compatibility10
- Install a Platelet Agitator in the Platelet Incubator11
- External Monitoring Devices11
- Configure Drawers (Pc4200I)12
- Drawer Labels12
3 Temperature Monitor Settings13
- Home Screen14
- Main Screen15
- Change Configuration Password16
- Calibrate Temperature Probes16
- Factory Default Settings17
- Alarm Reference17
- Alarm Settings18
- Alarm Tests21
- Agitrak™ System25
- Additional System Settings26
- Event Log30
- System Firmware Upgrade31
- Reset the I.center Monitoring System31
- View Manufacturer and Product Information31
4 Temperature Controller Setpoints32
- Level 1 Parameters and Values33
- Level 2 Parameters and Values34
- Level 3 Parameters and Values34
- Level 4 Parameters and Values35
- Platelet Incubator Setpoint35
- Calibrate the Temperature Controller Display36
5 Maintenance37
- Recharge Refrigerant37
- I.center Batteries38
- Motion Alarm Battery (Pc4200I)38
- Clean the Platelet Incubator39
- Lubricate the Drawer Slides (Pc4200I)39
- Lubricate and Service Internal Parts (Pc4200I)40
6 Troubleshooting41
- General Operation Problems41
- Chamber Temperature Problems43
- Alarm Activation Problems43
- Testing Problems45
- Condensation Problems46
7 I.series Parts47
8 Schematics54
- Pc100I, Pc900I, Pc1200I (100/115 V)54
- Pc100I, Pc900I, Pc1200I (230 V)55
- Pc2200I (115 V)56
- Pc2200I (230 V)57
- Pc3200I (115 V)58
- Pc3200I (230 V)59
- Pc4200I (115 V)60
- Pc4200I (230 V)61
9 I.center Screen Reference62
Horizon Series™ Models64
10 Installation And Configuration64
- Install Battery for Backup Power64
- Platelet Agitator and Platelet Incubator Compatibility64
- Install a Platelet Agitator in the Platelet Incubator65
- External Monitoring Devices65
- Configuring Drawers (Pc4200H)66
- Drawer Labels67
11 Alarm Settings68
- Temperature and Power Failure Alarm Volume68
- Motion Alarm (Pc4200H)69
- Alarm Tests70
12 Temperature Controller Setpoints73
- Level 1 Parameters and Values74
- Level 2 Parameters and Values75
- Level 3 Parameters and Values75
- Level 4 Parameters and Values76
- Change the Platelet Incubator Setpoint76
- Calibrate the Temperature Controller Display76
13 Maintenance78
- Recharge Refrigerant78
- Power Failure Alarm Battery79
- Motion Alarm Battery (Pc4200H)79
- Clean the Platelet Incubator80
- Lubricate the Drawer Slides (Pc4200H)80
- Lubricate and Service Internal Parts (Pc4200H)81
15 Horizon Parts87
16 Schematics94
- Pc100H, Pc900H, Pc1200H (100/115 V)94
- Pc100H, Pc900H, Pc1200H (230 V)95
- Pc2200H (115 V)96
- Pc2200H (230 V)97
- Pc3200H (115 V)98
- Pc3200H (230 V)99
- Pc4200H (115 V)100
- Pc4200H (230 V)101
Appendix A: Compliance102
Appendix B: Warranty103

Helmer PC100i - Service Manual

Table of Contents

Other manuals for Helmer PC100i

Related product manuals