How to troubleshoot Err30 on HemoCue Test Equipment?
If Err30 appears, it might be caused by dirty optical parts. Turn off the analyzer and clean the optical parts. If the optical parts were wet after cleaning, wait 15 minutes before turning the analyzer back on to ensure they are dry.
What to do if HemoCue Measuring Instruments shows Err01?
If your HemoCue Measuring Instruments displays Err01, it could be due to: 1. A measurement error: Take a new microcuvette and repeat the measurement. 2. An abnormal sample: The blood sample should be verified with a suitable laboratory method and be questioned as to the pathological condition of the patient.
Why does my HemoCue Measuring Instruments show Err30?
The Err30 error code on your HemoCue device may appear due to: 1. Dirty optical parts: Clean the optical parts after turning off the analyzer. 2. Wet optical parts after cleaning: Allow 15 minutes for the parts to dry before turning the analyzer back on.
What does Err34 mean on HemoCue Measuring Instruments?
If the HemoCue Measuring Instruments displays Err34, turn off the analyzer and ensure it is not exposed to bright light sources.
What does Err62 mean on HemoCue Test Equipment?
Err62 can mean that the blanking test failed or the optical parts are dirty. Turn off the analyzer, wait 30 seconds, and turn it on again. If the error persists, turn off the analyzer and clean the optical parts.
What does HHH mean on HemoCue Test Equipment?
Results exceeding the HHH limit should be verified with a suitable laboratory method and be questioned as to the pathological condition of the patient.
Why doesn't the HemoCue Measuring Instruments display switch to ready for measuring?
If the HemoCue Measuring Instruments display does not switch from “?” and “WbC” to three flashing dashes, it indicates that the cuvette holder sensor is out of order. The analyzer needs service; contact your local distributor.
Why is the HemoCue Measuring Instruments cuvette holder not moving correctly?
If the cuvette holder is not moving into the correct position, it suggests that the magnet in the cuvette holder is missing. The analyzer requires service; please contact your local distributor.
What does it mean when the HemoCue Measuring Instruments display shows blank spaces?
If the display shows only blank spaces, here’s what you should check: 1. If you're using batteries, they likely need replacement. Turn off the analyzer and replace the six AA batteries. 2. If using AC power, verify that the correct power adapter is properly connected and functioning. If problems persist, the circuit board might be faulty.
What does error Err03 mean on HemoCue Measuring Instruments?
To resolve Err03, take a new microcuvette and repeat the measurement.
Details the system's purpose for quantitative WBC determination and safety precautions.
Lists and describes the HemoCue WBC Analyzer and its associated components for setup.
Instructions for powering on, self-test, and readiness indicators.
How to activate or deactivate the audible signal for measurement alerts.
Procedure for connecting and using the printer to output results automatically.
Step-by-step guide for collecting capillary blood and preparing it for analysis.
Instructions for using control materials or venous blood samples for analysis.
Daily maintenance steps for cleaning the cuvette holder and cover.
Procedure for cleaning the analyzer's optical parts using the HemoCue Cleaner WBC.
Lists common error codes, their explanations, and recommended actions for resolution.
Troubleshooting steps for display errors, no characters, or cuvette holder movement problems.
Details the system's purpose, methodology, and operating principles.
Recommendations for storage, handling, and required materials for operation.
Information on internal quality control, self-tests, and expected blood cell count ranges.
Data on linearity, precision, and limitations of the measurement method.
Presents results from validation studies comparing HemoCue WBC to other methods.
Details substances that do not interfere with HemoCue WBC system performance.
Guidelines for operation in electromagnetic environments and compliance with EMC standards.
Specifications for AC adapters and warnings regarding electromagnetic interference.
Procedures for analyzer service, disposal, and available spare parts.
General| Sample Volume | 10 µL |
|---|---|
| Operating Temperature | 15 - 30 °C |
| Sample Type | Capillary, venous or arterial whole blood |
| Measurement Range | 0.3 - 30 x 10^9/L |
| Analysis Time | 3 minutes |
| Power Supply | AC adapter |
| Calibration | Factory calibrated, no user calibration required |
| Humidity | 10-90% non-condensing |
| Storage Temperature | 0 - 50 °C |
To Next Page
