What does error 'E-41' mean on Henny Penny EEG-242?
If the Henny Penny Fryer displays “E-41” or “E-46”, press the power button to turn the vat off and back on again. If the error codes persist, have the controls re-initialized. If the error code continues, the control board should be replaced.
What does 'E-20-B' mean on a Henny Penny EEG-242?
If your Henny Penny Fryer displays “E-20-B” and indicates “NO DRAFT” or “CHECK FAN”, press the power button to turn the vat off and back on. If the error persists, have the pressure switch checked to ensure it's an open circuit when there's no air pressure, and verify the hose is connected to both the fan and the pressure switch. Also, have the draft fan checked for low voltage and inspect the fryer flue and hood system for any obstructions.
What to do if Henny Penny EEG-242 shows 'E-20-D' ignition failure?
If the Henny Penny Fryer displays “E-20-D” and indicates an ignition failure, first, press the power button to turn the vat off and then back on. If the error persists, inspect the gas line connections, gas shutoff valve, ignition module, gas valve, flame sensor gap, and ignition module wiring. Also, check for and clear any obstructions from the atmospheric equalization hole in the regulator cap, as this can cause the pilot flame to fade slowly.
Why won't the filter motor run on my Henny Penny EEG-242 Fryer?
If the filter motor on your Henny Penny Fryer will not run, allow time for the motor to cool down. Then, using a screwdriver, press hard against the thermal reset button on the rear of the pump motor until it clicks.
Why won't oil drain from my Henny Penny EEG-242 Fryer?
If oil will not drain from the vat of your Henny Penny Fryer: * Open the valve and force a cleaning brush through the drain to clear any crumbs. * Remove the right side panel and remove the plug from the end of the trough to clean the trough.
Why is my Henny Penny EEG-242 Fryer not turning on?
If your Henny Penny Fryer is completely inoperative even when the power switch is ON: * Ensure the fryer is properly plugged in. * Check the breaker or fuse at the supply box.
General| Brand | Henny Penny |
|---|---|
| Model | EEG-242 |
| Category | Fryer |
| Language | English |
Provides troubleshooting information in an easy-to-read table format.
Explains safety symbols (DANGER, WARNING, CAUTION, NOTICE) and their meanings for hazard communication.
Details the process for isolating malfunctions: define problem, locate in table, review causes, and perform corrections.
Lists error codes, their causes (e.g., oil overheating, drain switch failure), and corrective actions.
Explains how to view actual oil temperature, set-point temperature, and recovery information for each vat.
Details how to check cook cycles remaining before filtering, time/date of last filter, and filter pad hours.
Describes accessing various logs and data like E-LOG, LAST LOAD, DAILY STATS, OIL STATS for operational and technical help.
Guides on how to program product names, assign buttons, change times, temperatures, and cook IDs.
Accesses detailed programming options like language, audio settings, melt cycle, idle mode, and filter tracking.
Instructions for setting the date, time, AM/PM, and time format (12/24 hour).
Lists self-diagnostic functions for technicians, including software, fryer type, push button tests, and probe calibration.
Allows technicians to view advanced operational information such as fryer running hours and oil temperatures.
Sets time periods when the "FILTER NOW?" message will not appear, for peak operation times.
Introduces maintenance procedures and provides tips for using a multimeter for checks.
Outlines regular maintenance tasks like filtering oil, changing filter pads, lubricating o-rings, and cleaning.
Instructions for replacing the control panel and menu card, including safety precautions.
Details the procedure for replacing the high temperature limit control, including disconnecting power and removing nuts.
Instructions for replacing the main power switch, including wire disconnection and reconnection.
Explains how to replace temperature and oil level probes, including Ohm checks and procedure.
Guides on checking solenoid valve resistance and replacing them, including removing panels and fittings.
Instructions for replacing the JIB pump, including removing shrouds, blower, flex lines, and pump feet.
Details replacing the blower, including removing back shroud, screws, zip ties, and wire nuts.
Steps to replace the filter beacon light, including removing side panels, pulling apart the light, and reconnecting wires.
Instructions for replacing air pressure switches, including removing shrouds, covers, hoses, and wires.
Guides on replacing the pilot, including removing burner tubes, flame sensor, screws, and pilot tube.
Introduces the section listing replaceable parts for the Evolution Elite® fryer.
Emphasizes using only genuine Henny Penny parts to avoid damage or injury.
Details the information needed when ordering parts, including item number, part number, and product/serial numbers.
Explains how to obtain pricing and delivery information for parts from distributors.
Outlines warranty coverage for replacement parts (90 days) and procedures for shipping damage claims.
To Next Page