Why is my Henny Penny Evolution Elite EEE-144 vat under-filled?
If the vat is under-filled, it could be due to a low or empty JIB, a clogged or collapsed JIB oil line, or a dirty filter pan. Fill the JIB, check the JIB line, and clean the filter pan, replacing the paper or pad.
What to do if my Henny Penny Fryer oil will not heat but lights are on?
If the oil isn't heating but the lights are on, ensure that both power cords are plugged in, as the unit requires two power cords to operate correctly.
What does Henny Penny Evolution Elite EEE-144 Fryer control error code “E-4” mean and how to fix it?
Error code E-4 indicates that the control board is overheating. Turn the switch to the OFF position, then back to ON. If the display continues to show “E-4”, check the louvers on each side of the unit for any obstructions.
What to do if my Henny Penny Evolution Elite EEE-144 Fryer filter motor will not run?
If the filter motor isn't running, first check that the power cord for vat #1 is plugged into the receptacle. Also, check for tripped breakers by opening the left door and resetting the breaker on the fryer. Another potential cause is a tripped thermal reset button on the rear of the pump motor. Allow the motor to cool, then use a screwdriver to press hard against the button until it clicks.
Why is my Henny Penny Evolution Elite EEE-144 Fryer POWER switch ON but fryer completely inoperative?
The fryer might not be working due to an open circuit. Ensure the fryer is properly plugged in and check the breaker or fuse at the supply box. For some international locations, there might be breakers in the fryer that have tripped open. If so, open the left door and reset the breaker on the fryer.
What does Henny Penny Evolution Elite EEE-144 control error code “E-18-A” “E-18-B” “E-18-C” mean?
Error codes E-18-A, E-18-B, and E-18-C indicate issues with the level sensors. E-18-A means the left level sensor is open, E-18-B means the right level sensor is open, and E-18-C means both level sensors are open. Turn the switch to the OFF position, then back to ON. If the display still indicates a failed sensor, have the connections checked at the control board. Have the sensor checked and replaced if necessary.
What does Henny Penny Fryer control error code “E-31” mean?
Error code E-31 indicates that the elements are up. Lower the elements back into the vat.
What does Henny Penny Evolution Elite EEE-144 control error code “E-15” mean?
Error code E-15 relates to the drain switch. Ensure the drain knob is completely pushed in. If the error persists, have the drain switch checked.
What to do if my Henny Penny Evolution Elite EEE-144 Fryer oil will not drain from vat?
If the oil won't drain from the vat, the drain valve might be clogged with crumbs, or the drain trough could be clogged. Open the valve and force a cleaning brush through the drain. Also, remove the right side panel, take out the plug from the end of the trough, and clean the trough.
What does Henny Penny Evolution Elite EEE-144 control error code “E-6B” mean?
Error code E-6B indicates the temperature probe is shorted. Turn the switch to the OFF position, then back to ON. If the display continues to show “E-6B”, the temperature probe should be checked.
General| Brand | Henny Penny |
|---|---|
| Model | Evolution Elite EEE-144 |
| Category | Fryer |
| Language | English |
Information on power supply, grounding, and electrical safety precautions.
Instructions on how to properly fill the fryer vat with oil.
Detailed guide on filtering the shortening to maintain oil quality.
Steps for performing a deep clean of the fryer using clean-out modes.
Guide to changing product names, times, temperatures, and other settings.
Guide to identifying and correcting common fryer issues and error messages.
To Next Page
