What to do if Henny Penny EVOLUTION ELITE EEG-241 Fryer displays error E-54C?
If your Henny Penny Fryer displays error code “E-54C”, it indicates a temperature input error. Turn the power switch to off, then back to on. If the error persists, have the control PC board replaced.
What to do if Henny Penny Fryer displays error E-48?
If your Henny Penny Fryer displays error code “E-48”, it indicates an input system error. Have the PC board replaced.
What to do if Henny Penny EVOLUTION ELITE EEG-241 displays error E-47?
If your Henny Penny Fryer displays error code “E-47”, it suggests an analog converter chip or 12-volt supply failure. Turn the power switch to vat off, then back to on. If the error persists, have the I/O board or the PC board replaced. If the speaker tones are quiet, it is probably an I/O board failure, so have the I/O board replaced.
What to do if Henny Penny EVOLUTION ELITE EEG-241 Fryer displays error E-41 or E-46?
If your Henny Penny Fryer displays error code “E-41” or “E-46”, it indicates a programming failure. Turn the power switch to vat off, then back to on. If the display continues to show an error code, have the controls re-initialized. If the error code persists, have the control board replaced.
What to do if Henny Penny EVOLUTION ELITE EEG-241 displays error E-18-A?
If your Henny Penny Fryer displays error code “E-18-A”, it indicates that the left level sensor is open. Turn the switch to the off position, then back to on. If the display still indicates a failed sensor, have the connections checked on the control board and have the sensor checked and replaced if necessary.
What to do if Henny Penny EVOLUTION ELITE EEG-241 displays error E-15?
If your Henny Penny Fryer displays error code “E-15”, ensure that the drain knob is completely pushed in. If the error persists, have the drain switch checked.
What to do if Henny Penny EVOLUTION ELITE EEG-241 displays error E-6B?
If your Henny Penny Fryer displays error code “E-6B”, it means the temperature probe is shorted. Turn the switch to the off position, then turn it back to on. If the display continues to show “E-6B”, the temperature probe should be checked.
What to do if Henny Penny Fryer displays error E-6A?
If your Henny Penny Fryer displays error code “E-6A”, it indicates that the temperature probe is open. Turn the switch to the off position, then turn it back to on. If the display continues to show “E-6A”, the temperature probe should be checked.
What to do if Henny Penny EVOLUTION ELITE EEG-241 displays error E-5?
If your Henny Penny Fryer displays error code “E-5”, it indicates that the oil is overheating. Turn the switch to the off position, then turn it back to on. If the display continues to show “E-5”, the heating circuits and temperature probe should be checked.
What to do if Henny Penny Fryer displays error E-20-D?
If your Henny Penny Fryer displays error code “E-20-D”, it indicates an ignition failure. First, press the power button to turn the vat off and then back on again. If the error persists, check the gas line connections and the gas shut-off valve. You should also have the ignition module checked, the gas valve checked, the flame sensor gap checked, and the wiring for the gas valve and ignition module checked. It could also be caused by a plugged atmospheric equalization hole in the regulator cap, resulting in a slowly fading pilot flame; if so, clear the obstruction from the hole.
General| Manufacturer | Henny Penny |
|---|---|
| Model | EVOLUTION ELITE EEG-241 |
| Category | Fryer |
| Fryer Type | Electric |
| Oil Capacity | 30 lbs per well |
| Temperature Range | 200°F - 375°F |
| Voltage | 208/240V |
| Phase | 1 |
To Next Page
