What to do if Henny Penny EVOLUTION ELITE EEG-243 displays error E-54C?
If your Henny Penny Fryer displays error code “E-54C”, it indicates a temperature input error. Turn the power switch to off, then back to on. If the error persists, have the control PC board replaced.
What to do if Henny Penny EVOLUTION ELITE EEG-243 displays error E-48?
If your Henny Penny Fryer displays error code “E-48”, it indicates an input system error. Have the PC board replaced.
What to do if Henny Penny EVOLUTION ELITE EEG-243 Fryer displays error E-47?
If your Henny Penny Fryer displays error code “E-47”, it suggests an analog converter chip or 12-volt supply failure. Turn the power switch to vat off, then back to on. If the error persists, have the I/O board or the PC board replaced. If the speaker tones are quiet, it is probably an I/O board failure, so have the I/O board replaced.
What to do if Henny Penny Fryer vat is under-filled?
If the vat of your Henny Penny Fryer is under-filled, here's what to check: * Make sure the BIB (Bag-In-Box) is not low or empty, and fill it if necessary. * Inspect the BIB oil line for clogs or collapses. * Ensure the filter pan is clean, and change the paper or pad.
What to do if Henny Penny EVOLUTION ELITE EEG-243 displays error E-18-A?
If your Henny Penny Fryer displays error code “E-18-A”, it indicates that the left level sensor is open. Turn the switch to the off position, then back to on. If the display still indicates a failed sensor, have the connections checked on the control board and have the sensor checked and replaced if necessary.
What to do if Henny Penny EVOLUTION ELITE EEG-243 displays error E-15?
If your Henny Penny Fryer displays error code “E-15”, ensure that the drain knob is completely pushed in. If the error persists, have the drain switch checked.
What to do if Henny Penny Fryer displays error E-6B?
If your Henny Penny Fryer displays error code “E-6B”, it means the temperature probe is shorted. Turn the switch to the off position, then turn it back to on. If the display continues to show “E-6B”, the temperature probe should be checked.
What to do if Henny Penny EVOLUTION ELITE EEG-243 Fryer displays error E-6A?
If your Henny Penny Fryer displays error code “E-6A”, it indicates that the temperature probe is open. Turn the switch to the off position, then turn it back to on. If the display continues to show “E-6A”, the temperature probe should be checked.
What to do if Henny Penny EVOLUTION ELITE EEG-243 Fryer displays error E-5?
If your Henny Penny Fryer displays error code “E-5”, it indicates that the oil is overheating. Turn the switch to the off position, then turn it back to on. If the display continues to show “E-5”, the heating circuits and temperature probe should be checked.
What to do if Henny Penny EVOLUTION ELITE EEG-243 Fryer displays error E-20-D?
If your Henny Penny Fryer displays error code “E-20-D”, it indicates an ignition failure. First, press the power button to turn the vat off and then back on again. If the error persists, check the gas line connections and the gas shut-off valve. You should also have the ignition module checked, the gas valve checked, the flame sensor gap checked, and the wiring for the gas valve and ignition module checked. It could also be caused by a plugged atmospheric equalization hole in the regulator cap, resulting in a slowly fading pilot flame; if so, clear the obstruction from the hole.
General| Manufacturer | Henny Penny |
|---|---|
| Model | EVOLUTION ELITE EEG-243 |
| Type | Fryer |
| Fryer Type | Electric |
| Oil Capacity | 30 lb per well |
| Voltage | 208-240V |
| Phase | 1 or 3 |
| Temperature Range | 200°F |
Defines safety alert symbols and their meanings.
Details on gas supply requirements and connection safety.
Procedure for performing a gas leak test after installation.
Specifies electrical requirements and grounding safety.
Guide to configuring initial fryer settings upon startup.
Instructions for filling the fryer vat with cooking oil.
Steps for starting the fryer at the beginning of the day.
Explains the standard procedures for operating the fryer.
Describes the automatic oil level monitoring and replenishment system.
Guide to performing a manual oil filtering procedure.
Instructions for running an automatic oil filtering procedure.
Procedure for a more thorough daily manual oil filtering.
Step-by-step guide for changing the fryer's filter pad.
Manual procedure for cleaning the fryer vat with cleaning solution.
Automatic procedure for cleaning the fryer vat using Smart Touch.
Common problems, their causes, and suggested corrections.
List of display error messages, causes, and corrective actions.
To Next Page
