Tools Required
HermanMiller
Renew
™
Table Installation
Y
How to assemble
your table
Parts Included
Work Surface Options
Rectangular Work Surface
Oval Work Surface
Switch
90° Work Surface 120° Work Surface
Power Driver
Philips-Recess Bit
Size: #2
Square-Recess Bit
Size: #2
Hex/Allen
Wrench Size:
5mm and
8mm
Torx Bit
Size: T30
Button Head
Screw
Tapping Screw
Socket
Glide
Lock Washer
Machine
Screw
© 2015 Herman Miller, Inc., Zeeland, Michigan Printed in U.S.A. Part No. 1bc4vh - E.
TM
Renew is among the trademarks of Herman Miller, Inc.
For more information about our products and services or to see a list of dealers,
For assistance: Please visit us at www.hermanmiller.com/product-instructions or call 888-443-4357
Illustrations and speci cations are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and speci cations at any time, without notice, and also to discontinue
products.
Base product number (DU)
Notice:
Some of the parts have been wrapped to protect them during shipping. Remove the plastic
wrap before assembling the table.
Assemble products on a protective surface.
Note: Not all the parts shown above are applicable for all the tables.
A
D
LegB
Extended
Corner Leg
Leg with
Hidden Power
Assembly
Peg
Foot
C
AA
F
Wire Cover
Tapping Hex
Head Screw
Cable Collector
Retainer Kit
Separates user power
cables from table
power cables
Hardware Kit
K
L
M
N
PR
S
T
V
Support Rail
G
E
T Leg Foot
C Leg Foot
H
J
WXY
Tapping Screw
Fastener
Extended Corner Work Surface
Control Box
Cable Clamp
Velcro
Z
AB
AC
IMPORTANT SAFETY INSTRUCTIONS
When using an electrical furnishing, basic precautions should always be followed, including
the following:
Read all instructions before using this furnishing.
DANGER - To reduce the risk of electric shock always unplug this furnishing from the
electrical outlet before cleaning.
WARNING - To reduce the risk of burns, re, electric shock, or injury to persons:
Close supervision is necessary when this furnishing is used by, or near children, invalids, or
disabled persons.
Sitting or standing on product may cause risk of personal injury (use for chairs, tables
consider obvious misuse of product).
Use this furnishing only for its intended use as described in these instructions. Do not use
attachments not recommended by the manufacturer.
Never operate this furnishing if it has a damaged cord or plug, if it is not working properly, if
it has been dropped or damaged, or dropped into water. Return the furnishing to a service
center for examination and repair.
Failure to fully tighten screws (bolts) may cause injury by causing Renew tables to collapse.
Tighten screws (bolts) until they stop plus a quarter turn.
Periodically check to make sure legs are properly aligned. Failure to do so may cause risk of
personal injury.
If using power drive set on low torque.
Keep the cord away from heated surfaces.
Never drop or insert any object into any opening.
Do not use outdoors.
Do not operate where aerosol (spray) products are being used or where oxygen is being
administered.
This furnishing is intended for commercial use
control box rating: 4.8A, 120V
Max FPDU rating: 15A, 120V
Duty cycle: 1min on, 18min o
Use extension bit if required, Magnetic bits are recommended.
Not all tools are used on all tables.
AD
Logic Unit
AE Clamp
AF Screw
HermanMiller Renew
TM
Table (Height Adjustable - Electrical) Assembl
Instructions1
Part no. 1bc4vh rev F
SAVE THESE INSTRUCTIONS
To Next Page
Need help?
General
