Need help?Do you have a question about the HIKVISION DS-2CD2443G0-I and is the answer not in the manual?
General| Number of lenses | 1 |
|---|---|
| Fixed focal length | 2.8 mm |
| Maximum aperture number | 1.6 |
| Minimum aperture number | 1.2 |
| Noise reduction | Yes |
| Total megapixels | 4 MP |
| Gain control type | Auto |
| Maximum resolution | 2688 x 1520 pixels |
| Image quality adjustment | Brightness, Contrast, Saturation, Sharpness |
| Video compression formats | H.264, H.264+, H.265, H.265+, M-JPEG |
| Noise reduction technology | 3D noise reduction |
| Supported graphics resolutions | 320 x 240, 352 x 240, 352 x 288, 640 x 360, 640 x 480 (VGA), 1280 x 720 (HD 720), 1920 x 1080 (HD 1080), 2304 x 1296, 2560 x 1440, 2688 x 1520 |
| Sensor type | CMOS |
| Optical sensor size | 1/3 \ |
| Pan range | 0 - 360 ° |
| Tilt angle range | 0 - 90 ° |
| Angle of rotation | 360 ° |
| Camera shutter speed | 1/3 - 1/100000 s |
| Minimum illumination | 0 lx |
| Type | IP security camera |
| Placement supported | Indoor |
| Connectivity technology | Wired |
| Built-in HDD | No |
| Compatible memory cards | MicroSD (TransFlash), MicroSDHC, MicroSDXC |
| Maximum memory card size | 128 GB |
| Alert notification type | |
| Intelligent Video Surveillance (IVS) system features | Face detection |
| Number of users | 32 user(s) |
| User access level | Administrator, Operator, User |
| Cabling technology | 10/100Base-T(X) |
| Networking standards | IEEE 802.1x, IEEE 802.3af |
| Ethernet interface type | Fast Ethernet |
| Supported network protocols | TCP/IP, UDP, ICMP, HTTP, HTTPS, FTP, DHCP, DNS, DDNS, RTP, RTSP, RTCP, PPPoE, NTP, UPnP, SMTP, SNMP, IGMP, 802.1X, QoS, IPv6, UDP, Bonjour, SSL/TLS |
| Sample rate | 48 kHz |
| Voice codecs | G.711alaw, G.711ulaw, G.722.1, G.726, MP2L2, PCM |
| Behavior analysis | Intrusion detection, Line crossing detection |
| Operating temperature (T-T) | -10 - 40 °C |
| Operating relative humidity (H-H) | 0 - 95 % |
| DC output current | 0.5 A |
| DC output voltage | 12 |
| Power source type | DC, PoE |
| Power consumption (max) | 6 W |
| Power consumption (Power over Ethernet (PoE)) | 7 W |
| LED type | IR |
| Infra-red wavelength | 850 nm |
| Night vision distance | 10 m |
| Form factor | Cube |
| Mounting type | Desk |
| Product color | Black, White |
| Housing material | Plastic |
Weight and Dimensions| Depth | 32.6 mm |
|---|---|
| Width | 65.2 mm |
| Height | 102.8 mm |
| Weight | 128 g |
Illustrates the physical appearance of the Type I and Type II network cube camera models.
Illustrates the physical appearance of the Type III network cube camera model.
Steps for inserting and securing a memory card into the camera.
General instructions for mounting Type I and Type II cameras.
Detailed steps for mounting Type I and Type II cameras using the stand.
Detailed steps for mounting Type I and Type II cameras onto a ceiling.
Instructions for mounting Type III cameras onto walls or ceilings.
Illustrates direct and switch/router network connection methods.
Procedures for activating the camera, including web browser and SADP methods.
Step-by-step guide to activate the camera through a web browser interface.
Step-by-step guide to activate the camera using the SADP software.
Instructions for changing the camera's IP address using SADP software.
Steps to enable the Hik-Connect service on the camera.
Guide to enable Hik-Connect service using SADP software.
Guide to enable Hik-Connect service using the web browser interface.
Instructions for downloading, installing, and registering for the Hik-Connect app.
Steps to connect the camera to your Hik-Connect mobile account.
Steps to initialize the memory card for event-triggered video recording.
To Next Page