HIKVISION DS-K4T100

Title:
DS-K4T100 Electric Lock Connect to
DS-K2600&DS-K2800 serires Access
Controller
Version:
v1.0
Date:
3/19/2018
Product:
Access Control Device
Page:
1 of 10
DS-K4T100 Electric Lock Connect to DS-K2600&DS-
K2800 serires Access Controller
Preparation
Connecting electric lock to access controller is mainly applied to open the door for exiting. For electric
lock and access controller in this document, please check the table below:
Magnetic Lock
Access Controller
DS-K4T100
DS-K2601, DS-K2602, DS-K2604
DS-K2801, DS-K2802, DS-K2804
Note
This document is simply used to guide users how to wire correctly and ensure access controllers can
control locks.
The access controller model in this document is DS-K2604 & DS-K2804.
Part 1 is mainly for electric lock wiring, and Part 2 and Part 3 are mainly for the situation that users could
get the door status on iVMS-4200 Client.
Notice
1. Please cut off power supply before wiring;
2. Please check interfaces of electric lock in following picture;
3. Correspondingly, there are lock and door magnetic interfaces in DS-K2800 & DS-K2600 series
access controllers, as pictures show:
Note: means lock interface; means door magnetic interface;
Access Controller
Interface
DS-K2801
Color
Description
Red
12V
Black
GND
Green
COM
Yellow
NC
Blue
NO

HIKVISION DS-K4T100 Specifications

General

Brand	HIKVISION
Model	DS-K4T100
Category	IP Access Controllers
Language	English

Summary

Preparation and Interface Identification

Electric Lock Wiring Preparation

Guidance on preparing for electric lock wiring, including power cutoff and interface checks.

Access Controller Interface Overview

Visual identification of lock and door magnetic interfaces on DS-K2600/DS-K2800 series controllers.

Part 1: Lock+ & Lock- Wiring

DS-K4 T100 Lock Wiring Examples

Illustrates wiring DS-K4T100 electric locks to DS-K2804 and DS-K2604 access controllers.

Part 2: Lock+Lock- & NCCOM Wiring

DS-K4 T100 NCCOM Connection

Wiring diagram for DS-K4T100 electric lock NC/COM terminals to DS-K2804 access controller.

Dual DS-K4 T100 NCCOM Connection

Wiring diagram for dual DS-K4T100 electric locks NC/COM terminals to DS-K2604 access controller.

iVMS-4200 Client Configuration and Monitoring

Add Access Controller to iVMS-4200

Steps to add the access controller to the iVMS-4200 client software for management.

Device Arming Control and Status Check

How to check the access controller's arming status using iVMS-4200 Device Arming Control.

Door Magnetic Sensor Parameter Setup

Configure Door Magnetic Sensor settings within iVMS-4200 Access Control Parameters.

Door Status Monitoring in iVMS-4200

Monitor door status and magnetic lock LED status via the iVMS-4200 Status Monitor interface.

Part 3: Lock+Lock- & NOCOM Wiring

DS-K4 T100 NOCOM Connection

Wiring diagram for DS-K4T100 electric lock NO/COM terminals to DS-K2804 access controller.

Dual DS-K4 T100 NOCOM Connection

Wiring diagram for dual DS-K4T100 electric locks NO/COM terminals to DS-K2604 access controller.

iVMS-4200 Advanced Configuration

Door Magnetic Sensor Parameter Adjustment

Adjusting Door Magnetic Sensor settings to 'Remain Open' in iVMS-4200 Access Control Parameters.

Door Status Monitoring Scenarios

Checking door status and magnetic lock LED status in iVMS-4200 for various scenarios.

Alarm Event Scenarios

Magnetic Lock LED Status Anomalies

Explanation of abnormal magnetic lock LED status, including open door timeout and improper installation.