EasyManua.ls Logo

HIKVISION DS-PDBG8-EG2-WE - User Manual

HIKVISION DS-PDBG8-EG2-WE
142 pages
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
AX PRO
User Manual

Table of Contents

Other manuals for HIKVISION DS-PDBG8-EG2-WE

Questions and Answers

  • V
    vmathewsSep 4, 2025
    Why am I unable to send mails to Yahoo from my HIKVISION Security System?
    • C
      Connie SmithSep 4, 2025
      If you cannot send emails to Yahoo, the security level of your mailbox might be too high. Go to your mail account settings and enable 'less secure sign-in'.
  • D
    David KimSep 18, 2025
    What to do if the alarm clearing operation on the HIKVISION Security System panel does not produce the alarm clearing report?
    • G
      George MurphySep 18, 2025
      If there is no alarm, no report will be uploaded for arm clearing.
  • K
    kevinsullivanSep 16, 2025
    What to do if the HIKVISION Security System failed to send test mail?
    • P
      Peter LangSep 16, 2025
      If the test mail fails to send, review and correct the mailbox configuration information as shown in table 1/1.
  • R
    Robert SimpsonSep 14, 2025
    What to do if HIKVISION Security System zone triggered/fault?
    • N
      Nicole FitzgeraldSep 14, 2025
      Reset the detector.
  • C
    Carly WolfeSep 12, 2025
    What causes failure in arming HIKVISION Security System?
    • H
      hudsonshannonSep 13, 2025
      Arming may fail if the panel doesn't enable 'forced arming' and there's a fault in the zone. To fix this, either turn on 'forced arming' or restore the zone to its normal status.
  • T
    Teresa ButlerSep 12, 2025
    What to do if HIKVISION Security System zone is tamper-proof?
    • L
      Lauren GonzalezSep 12, 2025
      Ensure the tamper-proof button of the detector is held down.
  • K
    Kristin PottsSep 9, 2025
    What to do if my HIKVISION Security System failed to send mail during use?
    • A
      Ashley HarrisonSep 9, 2025
      If the system fails to send mail, it could be that the mailbox server has restricted access. Log in to your mailbox to check if it is locked.
  • T
    Timothy MyersSep 7, 2025
    Why am I unable to enter registration mode on my HIKVISION Security System?
    • B
      blake18Sep 7, 2025
      If you can't enter registration mode, it might be because the panel is in 'Hotspot' mode. Switch the panel to 'station' mode and try again.
  • C
    Connie BrooksSep 5, 2025
    What to do if HIKVISION Security System zone is offline?
    • M
      Michelle McdowellSep 5, 2025
      If a zone is offline, it's likely because the detector reports undervoltage. Replace the detector battery to resolve this.
  • T
    Travis SmithAug 20, 2025
    How to fix HIKVISION Security System IP conflict?
    • K
      Kenneth LewisAug 21, 2025
      To resolve an IP conflict, first, find the currently available IP address using the ping command. Then, change the IP address and log in again.

HIKVISION DS-PDBG8-EG2-WE Specifications

General IconGeneral
ModelDS-PDBG8-EG2-WE
CategorySecurity Sensors
Detection Range8 m
Detection Angle90°
Wireless Frequency868 MHz
Battery TypeCR123A
ConnectivityWireless
Battery Life3 years
Operating Temperature-10°C to 55°C
Power SupplyBattery
CompatibilityHIKVISION Alarm Panel

Related product manuals