HIKVISION DS-PDMCK-EG2-WE - Page 6

11
Specificaon
10
Operaon Cauon and Device Maintenance
- All the electronic operaon should be strictly compliance with the electrical safety regulaons, fire prevenon regulaons and other related
regulaons in your local region.
- Do not drop the device or subject it to physical shock, and do not expose it to high electromagnesm radiaon. Avoid the equipment
installaon on vibraons surface or places subject to shock (ignorance can cause equipment damage).
- Please make sure that the power has been disconnected before you wire, install or dismantle the device.
- If smoke, odors or noise rise from the device, turn off the power at once and unplug the power cable, and then please contact the service
center.
- Do not drop the device or subject it to physical shock, and do not expose it to high electromagnesm radiaon. Avoid the equipment
installaon on vibraons surface or places subject to shock (ignorance can cause equipment damage).
- Do not place the device in extremely hot (refer to the specificaon of the device for the detailed operaon temperature), cold, dusty or
damp locaons, and do not expose it to high electromagnec radiaon.
- The device for indoor use shall be kept from rain and moisture.
Exposing the equipment to direct sun light, low venlaon or heat source such as heater or radiator is forbidden (ignorance can cause fire
danger).
- Do not aim the device at the sun or extra bright places. A blooming or smear may occur otherwise (which is not a malfuncon however), and
affecng the endurance of sensor at the same me.
- Improper use or replacement of the baery may result in hazard of explosion. Replace with the same or equivalent type only. Dispose of
used baeries according to the instrucons provided by the baery manufacturer.
- Do not expose the device to the corrosive gas. Otherwise the equipment damage may occur.
- Do not expose the device to the explosive situaon.
Detecon gap According to the magnet detecon performance table
One reed switch Yes
External inputs 2
Shock detecon Yes
Tilt detecon Up to 25°
Tamper protecon Front & Back
LED indicator Green(MC), Orange(lt), Red(shock), Blue(alarm)
Encapsulated plasc Yes
Input opons Normal and Fast Sensivity with Pulse Count
Programmable pulse count Yes
Fast input sensivity 1ms
Normal input sensivity 30
0ms
Operang temperature
-10 °C to 55 °C (14 °F to 131 °F)
-10 °C to 40 °C (14 °F to 104 °F) Cerfied
Storage temperature -20 °C to 60 °C (-4 °F to 140 °F)
Operang humidity 10% to 90%
Dimension (H × W × D)
Sensor: 22.5mm × 103mm × 23.2mm
Magnet: 13mm × 34.4mm × 11.4mm
Weight 60 g
Wireless technology Tri-X Wireless Technology
Programming method Advanced Wireless Link
LED indicator On/Off
Shock sensivity adjustment High/Normal/Low
Tilt 5° to 25°
External Input 1 NC/NO, Roller Shuer (RS), Tamper
External Input 2 NC/NO, Roller Shuer (RS), Tamper
RS Pulse Count 2 to 30 Pulses
RS Pulse Count Timeout 10 to 60s
Environment temperature indicator Yes
2-way wireless communicaon Yes
Transmiss
ion frequency 868MHz
Frequency hopping Mulchannel transmisson
Transmission encrypon AES-128 encrypon
Signal strength indicators Yes
RF range 1.6 km (open area)
Enrolling methods Power up, Remote ID, QR code
Baery CR123A x 1 (included)
Standard baery life 3 years
6
Hangzhou Hikvision Digital Technology CO.,Ltd. No.555 Qianmo Road, Binjiang District, Hangzhou 310052, China