How to fix no water flowing in my Hilti Drill?
If no water is flowing in your Hilti Drill, the filter or water flow indicator might be blocked. Remove the filter or water flow indicator and flush it through.
What does it mean when the service indicator lights up on my Hilti Drill?
If the service indicator lights up on your Hilti Drill, it could mean that the carbon brush wear limit has almost been reached. In this case, have the carbon brushes replaced at the next opportunity. It can also mean that the carbon brushes have been changed and must be run in. Run in the carbon brushes by letting the machine run under no load for at least 1 minute without interruption.
What to do if the diamond core bit doesn’t rotate on my Hilti DD 30-W Drill?
If the diamond core bit doesn’t rotate on your Hilti Drill, it may be jammed in the base material. Ensure you guide the drilling machine in a straight line. To release it, disconnect the mains plug from the power outlet, grip the diamond core bit with a suitable open-end wrench close to the connection end, and rotate it.
Why does the diamond core bit have too much play in my Hilti Drill?
If the diamond core bit has too much play in your Hilti Drill, the connection end might be defective. Check it and replace it if necessary. Also, ensure that the chuck lever is closed.
What to do if the diamond core bit can’t be fitted into the chuck of my Hilti DD 30-W Drill?
If the diamond core bit can’t be fitted into the chuck of your Hilti Drill, the core bit connection end or chuck might be dirty or damaged. Clean the connection end and/or the chuck, or replace these parts if necessary. Also, make sure the chuck operating lever is fully open.
Why doesn't my Hilti DD 30-W Drill achieve full performance?
If the diamond core drilling machine doesn’t achieve full performance, check whether other power consumers are disrupting the power supply from the network or generator. Also, check the length of the extension cord used.
Why does the service indicator show nothing on my Hilti DD 30-W Drill?
If the service indicator on your Hilti Drill shows nothing, first check that the PRCD is functioning and switched on. If that's not the issue, there may be an interruption in the electric supply. Plug in another electric tool or appliance to check if it works, and inspect the plug connections, supply cord, power supply line, and main supply fuse. Another potential cause is water in the motor. If this is the case, allow the drill to dry out completely in a warm, dry place.
Why is water escaping from the chuck during operation of my Hilti DD 30-W?
If water escapes from the chuck of your Hilti Drill during operation, it could be due to a dirty core bit connection end or chuck. Try cleaning these parts. Alternatively, the chuck seal may be defective, in which case you should check the seal and replace it if necessary.
What to do if water escapes from the chuck during operation of my Hilti Tools?
If water is escaping from the chuck during operation, it's likely that the core bit connection end or the chuck is dirty. Try cleaning the connection end or the chuck. If the problem persists, the chuck seal may be defective, requiring you to check the seal and replace it if necessary.
Why is the service indicator blinking on my Hilti Tools?
The service indicator may be blinking because the motor has overheated, possibly due to excessive lateral core bit friction or excessive contact pressure. To resolve this, wait a few minutes until the motor cools down, or allow the diamond core drilling machine to run under no load to speed up the cooling process. Switch the diamond core drilling machine off and then on again. Also, guide the diamond core drilling machine carefully, keeping it straight, and reduce the contact pressure.
Prerequisite for safe, trouble-free handling and use of the product.
Explanation of signal words, document symbols, and illustration symbols.
Details DANGER, WARNING, and CAUTION signal words and their meanings.
Lists and explains symbols used within the documentation's text.
Lists and explains symbols used within the document's illustrations.
Details symbols that are specific to the product itself.
Lists and explains symbols found on the actual product.
Details product type, generation, and serial number for identification.
Statement of compliance with applicable directives and standards.
Provides essential safety warnings and instructions for operating power tools.
Specific safety precautions and warnings for diamond drilling operations.
Covers personal safety, handling, and workplace safety aspects.
Identifies and describes the main components and features of the drilling machine.
Explains the function and components of the PRCD safety device.
Details the components and function of the water collection system.
Lists general accessories available for the product.
Lists accessories specific to the DD-ST 30 drill stand.
Specifies how the product should be used and for what applications.
Outlines prohibited uses and conditions for the product.
Details the equipment required for different applications and drilling directions.
Explains the LED indicators for service and operating status.
Details the LED indicators for drilling performance and contact pressure.
Describes the machine's two-speed settings and their operation.
Lists the components included with the machine.
Lists specific accessory tools like core bits and breaking tools.
Provides technical specifications for the diamond coring machine.
Details the electrical specifications, including voltage, frequency, and current.
General preparations and safety checks before starting work.
Steps for setting up the machine for hand-held operation.
Instructions for attaching and adjusting the side handle.
Instructions for attaching and setting the depth gauge.
Instructions for attaching the spray guard for upward drilling.
Instructions for attaching and adjusting the water collector holder.
Steps for fitting or replacing the sealing ring for the water collector.
Instructions for securely fitting the core bit into the chuck.
Connects the vacuum cleaner to the water collection hose for dust removal.
Steps for setting up the drilling machine with the drill stand.
Attaching the water collector holder for drill stand operation.
Secures the drill stand and machine using a vacuum base plate.
Guides on placing the vacuum base plate correctly for stability.
Secures the drill stand to the vacuum base plate.
Attaches the drilling machine to the drill stand assembly.
Secures the drill stand using an anchor for increased stability.
Methods to accurately align the drilling setup with the target hole.
Steps to align the system when using a vacuum base plate.
Steps to align the system when secured with an anchor.
Connects power and water supply to the machine for operation.
Detailed instructions for performing drilling operations by hand.
Detailed instructions for performing drilling operations using the drill stand.
Specific guidance for using a 600 mm core bit, including predrilling.
Procedure for safely turning off the drilling machine.
Steps for safely removing the core bit and emptying any material.
Methods for extracting the drilled core material from the hole.
Guidelines for the safe and environmentally sound disposal of drilling slurry.
Procedure for replacing worn carbon brushes.
Instructions for cleaning the water flow sight glass for proper function.
Addresses issues when the machine is functional but shows indicators.
Troubleshoots common malfunctions and provides corrective actions.
Guidelines for the safe and environmentally sound disposal of drilling slurry.
General| Max. drilling depth | 400 mm |
|---|---|
| Voltage | 230 V |
| Dust Removal Available | Yes |
| Working Mode | Hammer drilling, Drilling |
| Frequency | 50-60 Hz |
| Length | 360 mm |
| Weight according to EPTA Procedure 01/2003 | 4.4 kg |
| Power Consumption | 800 W |
| Impact Rate | 4290 impacts/minute |
| Drilling Diameter | 4-30 mm |
| Tool Chuck Type | SDS-plus |
To Next Page
