Hilti GX 3 User Manual (English)

Other manuals for Hilti GX 3

Original Operating Instructions20 pages

Manual32 pages

Questions and Answers:

V
vramosSep 1, 2025
What to do if no fastener is driven intermittently with Hilti GX 3 Power Tool?
- S
  Shelby BridgesSep 1, 2025
  If your Hilti Power Tool is intermittently failing to drive fasteners, consider these points: * Ensure ambient conditions are within the permissible range as specified in the technical data. * Check that the gas can temperature is within the permissible range. * Remove and reinsert the gas can to eliminate gas bubbles in the regulating system. * Lift the tool completely away from the surface after driving each fastener.
J
Jason WhiteAug 30, 2025
Why do fasteners bend when using Hilti Power Tool?
- M
  mcintoshlouisAug 30, 2025
  If fasteners are bending when using your Hilti Power Tool, it could be due to: * The driving power being too low; adjust the fastener driving depth adjustment slider to the + position. * The fasteners being too long; use shorter fasteners. * The fastener guide not being held perpendicular to the working surface; press the nosepiece against the working surface, keeping the tool perpendicular.
S
Samantha RowlandAug 29, 2025
What to do if Hilti GX 3 Power Tool remains compressed?
- G
  gchavezAug 29, 2025
  If your Hilti Power Tool remains compressed, consider these solutions: * Remedy the incorrect piston position. * Remove any foreign objects or nails from around the fastener guide if the nail detector is jammed. * Release any jammed fasteners from the fastener magazine. * Remove the gas can, press the tool nosepiece against the working surface, and firmly pull the trigger if a nail is jammed under the lever ahead of the piston face.
J
Jerome DavisAug 27, 2025
What to do if fasteners break when using Hilti GX 3 Power Tool?
- H
  Heather JimenezAug 27, 2025
  If fasteners are breaking when using your Hilti Power Tool, consider the following: * The driving power may be too low; adjust the fastener driving depth adjustment slider to the + position. * The fasteners might be too long; try using shorter fasteners. * The supporting material could be too hard; consider using a DX fastening tool. * Ensure the fastener guide is perpendicular to the working surface by pressing the nosepiece against it.
N
ncarrAug 27, 2025
Why are fasteners frequently driven too deeply with my Hilti GX 3?
- M
  Michelle RobertsAug 27, 2025
  If your Hilti Power Tool is driving fasteners too deeply, it may be because: * The driving power is too high; adjust the fastener driving depth adjustment slider to the ? position. * The fasteners are too short; try using longer fasteners.
M
Mary MillerAug 25, 2025
What to do if fastener driving failure rate is too high with Hilti GX 3?
- P
  Patrick HaynesAug 25, 2025
  If you're experiencing a high failure rate when driving fasteners with your Hilti Power Tool, consider these factors: * Ensure the nosepiece is pressed firmly against the working surface, keeping the fastener guide perpendicular. * Verify that you are using the correct type of fastener. * If the supporting material is too hard, consider switching to a DX fastening tool.
Z
Zachary MartinezAug 23, 2025
Why are fasteners frequently driven to inadequate depth with my Hilti Power Tool?
- C
  Carol WelchAug 23, 2025
  If fasteners are not being driven to the correct depth with your Hilti Power Tool, it could be due to several reasons: * The driving power may be too low; adjust the fastener driving depth adjustment slider to the + position. * The fasteners might be too long; try using shorter fasteners. * The supporting material could be too hard; consider using a DX fastening tool. * The inlet/outlet valve might be clogged; clean the fastening tool and check how it is held.