d) Under abusive conditions, liquid may be ejec-
ted from the battery; avoid contact. If contact
accidentally occurs, flush with water. If liquid
contacts eyes, additionally seek medical help.
Liquid ejected from the battery may cause irritation
or burns.
5.1.6 Service
a) Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
5.2 Additional safety instructions
5.2.1 Personal safety
a) Wear ear protectors. Exposure to noise can cause
hearing loss.
b) Use auxiliary handle(s), if supplied with the tool.
Loss of control can cause personal injury.
c) Hold power tool by insulated gripping surfaces,
when performing an operation where the cutting
accessory may contact hidden wiring. Cutting ac-
cessory contacting a "live" wire may make exposed
metal parts of the power tool "live" and could give
the operator an electric shock.
d) Always hold the power tool securely with both
hands on the grips provided. Keep the grips dry,
clean and free from oil and grease.
e) Improve the blood circulation in your fingers by
relaxing your hands and exercising your fingers
during breaks between working.
f) Avoid touching rotating parts. Switch the power
tool on only after bringing it into position at
the workpiece. Touching rotating parts, especially
rotating insert tools, may lead to injury.
g) Activate the safety lock (forward / reverse switch
in the middle position) before storing or trans-
porting the power tool.
h) The appliance is not intended for use by chil-
dren, by debilitated persons or those who have
received no instruction or training.
i) Children must be instructed not to play with the
appliance.
j) Dust from material such as paint containing lead,
some wood species, minerals and metal may be
harmful. Contact with or inhalation of the dust
may cause allergic reactions and/or respiratory
diseases to the operator or bystanders. Certain
kinds of dust are classified as carcinogenic such
as oak and beech dust especially in conjunction
with additives for wood conditioning (chromate,
wood preservative). Material containing asbestos
must only be treated by specialists. Where the
use of a dust extraction device is possible it
shall be used. To achieve a high level of dust
collection, use a suitable vacuum cleaner of the
type recommended by Hilti for wood dust and/or
mineral dust together with this tool. Ensure that
the workplace is well ventilated. The use of a
dust mask of filter class P2 is recommended.
Follow national requirements for the materials
you want to work with.
5.2.2 Power tool use and care
a) Secure the workpiece. Use clamps or a vice
to secure the workpiece. The workpiece is thus
held more securely than by hand and both hands
remain free to operate the power tool.
b) Check that the insert tools used are compatible
with the chuck system and that they are secured
in the chuck correctly.
5.2.3 Battery tool use and care
a) Ensure the switch is in the off position before
inserting battery pack. Inserting the battery pack
into power tools that have the switch on invites
accidents.
b) Do not expose batteries to high temperatures or
fire. This presents a risk of explosion.
c) Batteries must not be opened or dismantled,
squashed, heated to temperatures over 100°C
or incinerated. A risk of fire, explosion or in-
jury through contact with caustic substances may
otherwise result.
d)
Avoid ingress of dampness.
Dampness may cause
a short circuit resulting in a risk of burning injury
or fire.
e) Do not use batteries other than those approved
for use with the applicable power tool or appli-
ance. Use of other batteries or use of the battery
for purposes for which it is not intended presents
a risk of fire and explosion.
f) Observe the special instructions applicable to the
transport, storage and use of Li-ion batteries.
g) Avoid short-circuiting the battery. Check that the
terminals on the battery and in the power tool
are free from foreign objects before inserting
the battery in the power tool. Short circuiting the
battery terminals presents a risk of fire, explosion
and chemical burns.
h) Do not charge or continue to use damaged bat-
teries (e.g. batteries with cracks, broken parts,
bent or pushed-in and/or pulled-out contacts).
i) If the battery gets too hot to touch, this may
indicate that it is faulty. Place the tool at a location
where there is no risk of causing a fire (at least 3
meters away from flammable materials), where
it can be kept under observation and allowed to
cool. Contact Hilti Service after the battery has
been allowed to cool.
5.2.4 Electrical safety
Before beginning work, check the working area
(e.g. using a metal detector) to ensure that no
concealed electric cables or gas and water pipes
are present. External metal parts of the power tool
may become live, for example, when an electric cable
is damaged accidentally. This presents a serious risk
of electric shock.
5.2.5 Work area
a) Ensure that the workplace is well lit.
b) Ensure that the workplace is well ventilated.
Exposure to dust at a poorly ventilated workplace
may result in damage to the health.
5.2.6 Personal protective equipment
The user and any other persons in the vicinity must
wear suitable eye protection, a hard hat, ear pro-
tection, protective gloves and breathing protection
while the tool is in use.
6. Before use
6.1 Battery use and care
NOTE
Battery performance drops at low temperatures. Use
a battery only when it has been fully charged. This
ensures that maximum battery capacity is available.
Change to the second battery as soon as a drop in
performance is noticed. Recharge the battery imme-
diately so that it is ready for reuse.
Store the battery in a cool, dry place. Never store
the battery where it is exposed to direct sunlight or
sources of heat, e.g. on heaters / radiators or behind a
motor vehicle windscreen. Batteries that have reached
the end of their life must be disposed of safely and
correctly to avoid environmental pollution.
6.2 Charging the battery
DANGER
Use only the Hilti batteries and Hilti chargers listed
under “Accessories”.
6.2.1 Charging a new battery for the first time
Charge the battery fully before using it for the first
time.
6.2.2 Charging a previously used battery
Ensure that the outer surfaces of the battery are
clean and dry before inserting it in the corresponding
charger.
To Next Page
Loading...
Need help?
General
Weight and Dimensions
