Hilti SFC 14-A User Manual (English)

Other manuals for Hilti SFC 14-A

Manual20 pages

Operating Instructions12 pages

Questions and Answers:

M
Mikayla CookAug 20, 2025
What to do if Hilti SFC 14-A Drill doesn't work?
- B
  Bryan AlexanderAug 20, 2025
  If your Hilti Drill isn't working, there are several potential causes. First, ensure the battery is fully inserted until you hear a double click. If that's not the issue, the battery might be low, so try changing it and charging the depleted one. If these steps don't resolve the problem, there may be an electrical fault. In this case, remove the battery from the tool and contact Hilti Service.
M
Ms. Vanessa ValentineAug 22, 2025
What to do if Hilti SFC 14-A battery does not engage?
- J
  Jeffrey JohnsonAug 22, 2025
  If the Hilti Drill battery doesn't engage with a double click, the retaining lugs on the battery might be dirty. Clean the retaining lugs and then push the battery in until it engages. If the problem continues, contact Hilti Service.
J
Jessica MezaAug 25, 2025
Why does my Hilti SFC 14-A LED 1 flash?
- G
  Gregory BushAug 25, 2025
  If LED 1 is flashing on your Hilti Drill, it could be due to a low battery. Try changing the battery and charging the empty one. Alternatively, the tool might be overloaded because the application limits have been exceeded. Ensure that you pay attention to the power and performance rating of the product before using it and check its suitability for the job.
D
Diane ParkAug 26, 2025
What to do if Hilti SFC 14-A Drill doesn't work and LED flashes?
- D
  Donald ThomasAug 26, 2025
  If your Hilti Drill isn't working and an LED is flashing, it could be due to a low battery. Try replacing the battery and charging the depleted one. Another possibility is that the battery is either too hot or too cold. Allow the battery to reach the recommended operating temperature.
B
Benjamin HillAug 28, 2025
How to unlock the on/off button on a Hilti Drill?
- R
  randersonAug 28, 2025
  If the on/off button on your Hilti Drill is locked, it's likely because the forward/reverse selector switch is in the middle position. Simply push the forward/reverse switch to the left or right to unlock the button.
J
Jason CampbellAug 29, 2025
Why my Hilti Power Tool does not work?
- A
  Ashley HarringtonAug 29, 2025
  If your Hilti Power Tool isn't working, it could be due to a few reasons. First, make sure the battery is fully inserted until you hear a double click. If that's not the issue, the battery might be low, so try changing it and charging the empty one. If neither of these steps works, there may be an electrical fault. In this case, remove the battery and contact Hilti Service.
L
Laura DonaldsonAug 31, 2025
How to unlock the on/off button on Hilti Power Tool?
- G
  Gary MolinaAug 31, 2025
  If your Hilti Power Tool's on/off button is locked, it's likely because the forward/reverse selector switch is in the middle position. To unlock it, simply push the forward/reverse switch to either the left or right.
M
Michele RossSep 2, 2025
What to do if LED 1 flashes on my Hilti Power Tool?
- A
  Angela ThomasSep 2, 2025
  If the LED 1 flashes on your Hilti Power Tool, it could be due to a low battery. Try changing the battery and charging the empty one. Alternatively, the tool might be overloaded because you exceeded application limits. Check the 'Technical data' section to ensure the tool is suitable for the job.
A
amandawelchSep 4, 2025
What to do if Hilti Power Tool does not work and one LED flashes?
- S
  Susan WrightSep 4, 2025
  If your Hilti Power Tool does not work and one LED flashes, the battery might be low. Try replacing the battery and charging the depleted one. Alternatively, the battery could be too hot or too cold. Allow the battery to reach the recommended operating temperature.
M
Mallory KingSep 6, 2025
What to do if the battery does not engage with an audible double click on Hilti Power Tool?
- C
  Claire GrahamSep 6, 2025
  If the battery doesn't engage with an audible double click on your Hilti Power Tool, the retaining lugs on the battery might be dirty. Clean the retaining lugs and push the battery in until it engages. If the problem continues, contact Hilti Service.

Hilti SFC 14-A Specifications

General

Number of gears	2
Screw diameter (max)	8 mm
Sound pressure level	69 dB
Idle speed (1st gear)	1700 RPM
Drilling diameter in wood (max)	20 mm
Drilling diameter in steel (max)	10 mm
Vibration level (metal drilling)	2 m/s²
Maximum torque (hard applications)	45 N⋅m
Maximum torque (soft applications)	24 N⋅m
Product color	Black, Red
Chuck type	Keyless
Product design	Pistol grip drill
Number of batteries included	1 pc(s)
Power source	Battery
Battery voltage	14 V