Description
The TCU 7/36
charger
is designed
for
charging all
current Hilti batteries
with a nominal
voltage
of
7 to 36 volts,
The batteries it can charge are
BP 6-86
for
the
TE 6-4
cordless rotarv hammer
SBP
1O
for the SB 10 cordless screwdriver
SBP
12
for the
SB
12 cordless screwdriver
Technical data
Freo uencv
50/60
Hz
0utput
voltaqe
7.2-36.0
V
(max.
charging
voltage 54
V)
0utput
current for
nh^"^ih^
^,,v"^^+
-
uil4ruIrg uuilEilr
-
Trickle charqinq current
7.2-54.0 V
voltage range
2.5 A max..
0.15 A/0.05
A
Electronic charging control
Temperature monitoring
-
NTC
(BP
6-86,) and
-
Diode
(SBP
1 0,
SBP
1
2)
Charging
time
BP
6-86
60 min
SBP 10 48 min
SBP
12 48 min
lnsulation class
Electrical
insulation
class
| |
(double
insulated) E
Right o{ technical changes reserved
tAl
5.
4) Handle the supply cord
carelully.
Never carry
the charger by the supply cord.
Don't unplug
the charger by
pulling
on the supply cord.
Don't expose
the
supply
cord
to heat,
oil or
sharp edges.
lf the
sup-
ply
cord becomes
damaged while
working, don't touch
it
-
unplug
the
mains
plug
immediately.
.N
6.
lzf
Keeplhe
chargerand
batteriesin
good
con-
dition.
Follow
the instructions on care and maintenance.
Nev-
er
0perate
the
charger
when it is dirty or
wet.
Under
unfavourable
conditions, dampness or
dirt adherlng
to
the surface
of the charger may
present
a
risk of electric
sh ock.
Repairs
t0 the
charger
including, in
pafiicular,
replace-
ment of the supply cord,
may be canied out only by
the
manufacturer
or authorised service
centre using origi-
nal Hilti spare
parts.
Failure to observe this
point
may
result in damage 0r
present
a
risk of accident.
Accord-
ingly, if necessary,
have
the charger
repaired at a Hilti
service centre or
authorised Hilti
repair
workshop.
A
surrty
precautions
When using electric
appliances,
the
following
f
unda-
mental safety
precautions
must always be observed
in
order
to avoid the risk of injury, electric
shock and fire
hazards.
Please read and
observe
the
instructions below
before
using the appliance.
t^ l
1.
lZ\
4uo;X short circuits.
Short circuiting
the contacts of
the
charger
or
battery
oresents a risk of
fire.
2.
Take the inlluences
ol
lhe surrounding
area into
account.
Don't expose the charger to rain and don't
use it in damp
0r
wet
surroundings
or in the vicinity of
flammable liq-
uids
or
gases.
,\-
g.
lZ\
cneck the charger each
time belore use.
Checkthe condition
ofthe charger, supply
cord and
plug.
Don't use the charger
if it is found to be damaged,
incom-
plete
or if the controls cannot
be operated c0rrectly.
4. Use
the
chalger
only lor the
puryose
for which it is
intended.
To Next Page
Loading...
Need help?
General
