SPECIFICATION
The HTF-2 Floor Sander will sand wood floors,
including fine parquet, pre-finished and laminate
wood flooring systems, cork and composition floors
to a fine finish. Ideal for sanding between coats of
floor varnish and lacquers were a very high quality,
score free finish is required. The finally balanced
orbital action will not leave swirl marks in the floor
surface which may be highlighted when varnished.
Designed for sanding floors that are level and in
generally good condition were the existing varnish
has worn and requires re-finishing. Completely self
contained with a powerful dust pickup the HTF-2 is a
high performance floor sander suitable for
professional and home owner use.
SAFETY
1. For safety it is recommended that a residual
current circuit breaker (ground fault interrupter)
is used with this machine.
2. Check the operating voltage is correct and that
the machine is switched OFF (O) before
connecting to the power supply.
3. Never attempt to lock the switch in the ON (I)
position with tape or by any other means.
4. Always disconnect from the power supply when
changing the abrasive, servicing the floor
sander, replacing the dust bag or leaving the
machine unattended.
5. Always replace the dust bag when the dust in the
bag reaches the ‘MAX’ line or when the machine
is left unattended.
6. Never dispose of or empty the contents of the
dust bag into a fire or incinerator.
7. Never reuse the paper dust bag or use a non
standard bag.
8. Always wear a dust mask when using the floor
sander, handling the dust bag or cleaning the
machine after use.
9. Wear ear protection when using the floor sander.
10. Ensure adequate ventilation of the work area to
avoid the formation of a combustible mixture of
flying dust and air.
11. Never smoke when using or servicing the floor
sander or when handling the dust bag. Make
sure thast all possible sources of ignition are
removed from the work area.
12. Never expose the machine to rain or damp.
Always store in a dry place.
13. Stop the floor sander immediately if damage to
the machine or abrasive is suspected.
14. Never allow the power cable to come into contact
with the sanding pad when the floor sander is in
operation. If the power cable becomes damaged
and the inner conductors are exposed switch the
power OFF (O) and remove the plug before
attempting to move the machine. The cable must
be replaced by an authorized agent or qualified
electrician using genuine spare parts only.
15. Keep hands, feet and loose clothing away from
all moving parts of the machine.
16. Punch down or remove all nails, screws, tacks
and other fixings from the floor before sanding to
prevent contact with the sanding pad.
17. Keep children and pets clear at all times.
18. If the machine should fail to operate refer to the
fault finding guide on page 9.
Hiretech®
1
Read the following Safety and
Operational notes before using your
HTF-2 Floor Sander.
Noise: 95 dBa at 1metre (3’ 3")
Switch: Bias Off, double pole.
Motor RPM:
10,000
Sanding Pad
RPM:
3,000
Moving Parts: Sealed for life ball bearings.
Weight:
43kg (94.8lbs)
0.09 M² H Aeq8
(8 Hr. RMS )
400mm (15¾") x 115mm
(4½") random fibre abrasive
pad 280 grit and backing pad.
400mm (15¾") x 115mm
(4½") anti-clog adhesive
backed sheet 40 to 180 grit.
Abrasive:
Continuous heavy duty AC/DC
self cooling 4 brush.
400mm (15¾") x 115mm 4½"
MDF back with 4½" MDF
back with
Non-slip toothed timing belt
and toughened steel pinion
and drive gear.
Seated oversize vacuum fan,
disposable paper dust or cloth
bag.
Drive:
Dust Pickup:
Vibration:
Motor:
Sanding Pad:
110/120 V 50/60 Hz
220/240 V 50/60 Hz
110/120 V 8A
220/250 V 5A
Average
Load Current:
110/120 V 15A
220/250 V 8A
Power Supply:
Off Load
Current:
To Next Page
Loading...
