Hitachi CP-WX8265 User Manual

91
SECURITY menu
This projector is equipped with security functions.
From the SECURITY menu, items shown in the table
below can be performed.
To use SECURITY menu: User registration is required
before using the security functions.
Enter to the SECURITY menu
1. Press the ► button. The ENTER PASSWORD box will be displayed.
2. Use the ▲/▼/◄/► buttons to enter the registered password. The
factory default password is as follows.
CP-X8170: 3805
CP-WX8265: 2205
CP-WU8460: 3905
This password can be changed
(

below)
. Move the cursor to the
right side of the ENTER PASSWORD box and press the ► button to
display the SECURITY menu.
• It is strongly recommended the factory default password to be
changed as soon as possible.
• If an incorrect password is input, the ENTER PASSWORD box
will be displayed again. If incorrect password is input 3 times, the
projector will turn off. Afterwards the projector will turn off every time
an incorrect password is input.
3. Items shown in the table below can be performed.
If you have forgotten your password
(1) While the ENTER PASSWORD box is displayed, press and hold the
RESET button on the remote control for about 3 seconds or press
and hold the INPUT button for 3 seconds while pressing the ►
button on the projector.
(2) The 10 digit Inquiring Code will be displayed. Contact your dealer
with the 10 digit Inquiring Code. Your password will be sent after
your user registration information is conrmed.
• If there is no key input for about 55 seconds while the Inquiring Code is displayed, the menu will
close. If necessary, repeat the process from (1).
Item Description
SECURITY
PASSWORD
CHANGE
(1) Use the ▲/▼ buttons on the SECURITY menu
to select SECURITY PASSWORD CHANGE
and press the ► button to display the ENTER
NEW PASSWORD box.
(2) Use the ▲/▼/◄/► buttons to enter the new password.
(3) Move the cursor to the right side of the ENTER
NEW PASSWORD box and press the ► button
to display the NEW PASSWORD AGAIN box,
enter the same password again.
(4)
Move the cursor to the right side of the NEW
PASSWORD AGAIN box and press the ►
button and the NOTE NEW PASSWORD box
will be displayed for about 30 seconds, please
make note of the password during this time.
Pressing the ENTER button on the remote control or ► button on the
projector will close the NOTE NEW PASSWORD box.
• Please do not forget your password.
(continued on next page)
SECURITY menu

Hitachi CP-WX8265 Specifications

General

Number of colors	16.78 million colors
Native aspect ratio	4:3
Projection distance	0.94 - 18.41 m
Projection technology	3LCD
Supported aspect ratios	16:9, 16:10
Contrast ratio (typical)	3000:1
Screen size compatibility	30 - 300 \
Projector native resolution	WXGA (1280x800)
Vertical synchronization (max)	120 kHz
Vertical synchronization (min)	56 kHz
Keystone correction, horizontal	-35 - 35 °
Horizontal synchronization (max)	106 kHz
Horizontal synchronization (min)	31.5 kHz
Throw ratio	1.5 - 3.0:1
Digital zoom	2 x
Focal length range	24 - 48 mm
Aperture range (F-F)	1.6 - 2.9
RS-232 ports	1
Maximum analog resolution	1600 x 1200 pixels
Lamp power	365 W
Light source type	Lamp
Service life of light source	2000 h
Service life of light source (economic mode)	2500 h
Full HD	No
Analog signal format system	NTSC, NTSC 4.43, PAL, PAL M, PAL N, SECAM
Supported graphics resolutions	1024 x 768 (XGA), 1280 x 1024 (SXGA), 1280 x 800 (WXGA), 1400 x 1050 (SXGA+), 1440 x 900 (WXGA+), 1600 x 1200 (UXGA), 640 x 480 (VGA), 800 x 600 (SVGA)
Built-in display	Yes
BNC input ports	5
USB connector type	USB Type-A, USB Type-B
Serial interface type	RS-232
USB 2.0 ports quantity	3
Ethernet LAN data rates	100 Mbit/s
Noise level	39 dB
Noise level (economic mode)	33 dB
Product type	Standard throw projector
Product color	White
Cable lock slot type	Kensington
Power source	AC
AC input voltage	100 - 240 V
AC input frequency	50 - 60 Hz
Power consumption (standby)	- W
Power consumption (typical)	500 W

Weight and Dimensions

Depth	396.2 mm
Width	497.8 mm
Height	134.6 mm
Weight	8800 g