Hitachi SJ700-220HFEF2

To Next Page

To Previous Page

Code

Function Name

Default Setting

-FE(CE) -FU(UL)

Change

during operation

(allowed or not)

Setting

during operation

(allowed or not)

Monitored data or setting

Intelligent output terminalsAnalog monitoringLevels and output terminal statusCommunication functionAdjustmentOthers

Intelligent

output terminals

Intelligent input terminals

Terminal (1) active state

Terminal (2) active state

Terminal (3) active state

Terminal (4) active state

Terminal (5) active state

Terminal (6) active state

Terminal (7) active state

Terminal (8) active state

Terminal FW active state

FM signal selection

AM signal selection

AMI signal selection

Digital current monitor reference value

Terminal (11) active state

Terminal (12) active state

Terminal (13) active state

Terminal (14) active state

Terminal (15) active state

Alarm relay terminal active state

Low-current indication signal output mode selection

Low-current indication signal detection level

Overload signal output mode

Overload level setting

Frequency arrival setting for accel.

Frequency arrival setting for decel.

PID deviation level setting

Frequency arrival setting for acceleration (2)

Frequency arrival setting for deceleration (2)

Maximum PID feedback data

Minimum PID feedback data

Over-torque(Forward-driving) level setting

Over-torque(Reverse-regenerating) level setting

Over-torque(Reverse-driving) level setting

Over-torque(Forward-regenerating) level setting

Electronic thermal warning level setting

Alarm code input

Zero speed detection level

Heat sink overheat warning level

Communication speed selection

Node allocation

Communication data length selection

Communication parity selection

Communication stop bit selection

Selection of the operation after communication error

Communication timeout limit before tripping

Communication wait time

Communication mode selection

O input span calibration

OI input span calibration

O2 input span calibration

Thermistor input tuning

Debug mode enable

UP/DOWN memory mode selection

Reset mode selection

Restart mode after reset

FM gain adjustment

AM gain adjustment

C011

C012

C013

C014

C015

C016

C017

C018

C019

C027

C028

C029

C030

C031

C032

C033

C034

C035

C036

C038

C039

C040

C041

C042

C043

C044

C045

C046

C052

C053

C055

C056

C057

C058

C061

C062

C063

C064

C071

C072

C073

C074

C075

C076

C077

C078

C079

C081

C082

C083

C085

C091

C101

C102

C103

C105

C106

00 (RUN: running), 01 (FA1: constant-speed reached), 02 (FA2: set frequency overreached), 03 (OL:

overload notice advance signal (1)), 04 (OD: output deviation for PID control), 05 (AL: alarm signal), 06

(FA3: set frequency reached), 07 (OTQ: over-torque), 08 (IP: instantaneous power failure), 09 (UV:

undervoltage), 10 (TRQ: torque limited), 11 (RNT: operation time over), 12 (ONT: plug-in time over), 13

(THM: thermal alarm signal), 19 (BRK: brake release), 20 (BER: braking error), 21 (ZS: 0 Hz detection

signal), 22 (DSE: speed deviation maximum), 23 (POK: positioning completed), 24 (FA4: set frequency

overreached 2), 25 (FA5: set frequency reached 2), 26 (OL2: overload notice advance signal (2)), 27 (Odc:

Analog O disconnection detection), 28 (OIDc: Analog OI disconnection detection), 29 (O2Dc: Analog O2

disconnection detection), 31 (FBV: PID feedback comparison), 32 (NDc: communication line disconnection),

33 (LOG1: logical operation result 1), 34 (LOG2: logical operation result 2), 35 (LOG3: logical operation

result 3), 36 (LOG4: logical operation result 4), 37 (LOG5: logical operation result 5), 38 (LOG6: logical

operation result 6), 39 (WAC: capacitor life warning), 40 (WAF: cooling-fan speed drop), 41 (FR: starting

contact signal), 42 (OHF: heat sink overheat warning), 43 (LOC: low-current indication signal), 44 (M01:

general-purpose output 1), 45 (M02: general-purpose output 2), 46 (M03: general-purpose output 3), 47

(M04: general-purpose output 4), 48 (M05: general-purpose output 5), 49 (M06: general-purpose output 6),

50 (IRDY: inverter ready), 51 (FWR: forward rotation), 52 (RVR: reverse rotation), 53 (MJA: major failure),

54(WCO: window comparator O), 55(WCOI: window comparator OI), 56 (WCO2: window comparator O2)

(When alarm code output is selected for "C062", functions "AC0" to "AC2" or "AC0" to "AC3" [ACn: alarm

code output] are forcibly assigned to intelligent output terminals 11 to 13 or 11 to 14, respectively.)

00 (output frequency), 01 (output current), 02 (output torque), 03 (digital output frequency), 04 (output

voltage), 05 (input power), 06 (electronic thermal overload), 07 (LAD frequency), 08 (digital current

monitoring), 09 (motor temperature), 10 (heat sink temperature), 12 (general-purpose output YA0)

00 (output frequency), 01 (output current), 02 (output torque), 04 (output voltage), 05 (input power), 06

(electronic thermal overload), 07 (LAD frequency), 09 (motor temperature), 10 (heat sink temperature), 11

(output torque [signed value]), 13 (general-purpose output YA1)

00 (output frequency), 01 (output current), 02 (output torque), 04 (output voltage), 05 (input power), 06

(electronic thermal overload), 07 (LAD frequency), 09 (motor temperature), 10 (heat sink temperature), 14

(general-purpose output YA2)

［◯ ］ ［◯

= Allowed

= Not permitted

］

［◯ ］

0.20 x "rated current" to 2.00 x "rated current" (A)

(Current with digital current monitor output at 1,440 Hz)

00(NO) / 01(NC)

00 (output during acceleration/deceleration and constant-speed operation),

01 (output only during constant-speed operation)

0.0 to 2.00 x "rated current" (A)

00 (output during acceleration/deceleration and constant-speed operation),

01 (output only during constant-speed operation)

0.0 to 2.00 x "rated current" (A)

0.00 to 99.99, 100.0 to 400.0 (Hz)

0.0 to 100.0 (%)

0.00 to 99.99, 100.0 to 400.0 (Hz)

0.0 to 100.0 (%)

0. to 200. (%)

0. to 100. (%)

00(Disabled) / 01(3-bit) / 02(4-bit)

0.00 to 99.99, 100.0 (Hz)

0. to 200.0 (

℃

)

02 (loopback test), 03 (2,400 bps), 04 (4,800 bps), 05 (9,600 bps), 06 (19,200 bps)

1. to 32.

7 (7 bits), 8 (8 bits)

00 (no parity), 01 (even parity), 02 (odd parity)

1 (1 bit), 2 (2 bits)

00 (tripping), 01 (tripping after decelerating and stopping the motor), 02 (ignoring errors),

03 (stopping the motor after free-running), 04 (decelerating and stopping the motor)

0.00 to 99.99 (s)

0. to 1000. (ms)

00(ASCII), 01(Modbus-RTU)

0. to 9999., 1000 to 6553(10000 to 65530)

0. to 9999., 1000 to 6553(10000

〜

65530)

0. to 9999., 1000 to 6553(10000

〜

65530)

0.0 to 999.9, 1000.

(Do not change this parameter, which is intended for factory adjustment.)

00 (not storing the frequency data), 01 (storing the frequency data)

00 (resetting the trip when RS is on), 01 (resetting the trip when RS is off),

02 (enabling resetting only upon tripping [resetting when RS is on])

00 (starting with 0 Hz), 01 (starting with matching frequency), 02 (restarting with active matching frequency)

50. to 200. (%)

00(NO) / 01(NC)

00



00



00



00



00

01



01



01



0.00

3.0

0.00

100.0

0.0

100.

80.

00

0,00

120.

04

1.

7

00

1



02

0.00

0.

00



00



00



100.

100.

00

01

00



00



00



00



00

01



01



01



0.00

3.0

0.00

100.0

0.0

100.

80.

00

0,00

120.

04

1.

7

00

1



02

0.00

0.

00



00



00



100.

100.

×



×



×



×



○



×



×



×



×



○



×

○



○



○



○



○



○



○



○



○



○



○



○

×

○



○



○

Rated current of

inverterx 1..0

Rated current of inverterx 1..0

Factory set

Terminal (11) function

Terminal (12) function

Terminal (13) function

Terminal (14) function

Terminal (15) function

Alarm relay terminal function

C021

C022

C023

C024

C025

C026

01(FA1)

00(RUN)

03(OL)

07(OTO)

40(WAF)

05(AL)



01(FA1)

00(RUN)

03(OL)

07(OTO)

40(WAF)

05(AL)



×



○



Meter

adjustment

Main Page

Hitachi SJ700-220HFEF2

Table of Contents

Related product manuals