Hitachi SJ700B SERIES - Page 272

Index
Index - 1
A
a/b............................................................4-47, 4-61
absolute position control ......................4-106, 4-107
acceleration/deceleration patterns ....................4-31
acceleration curve constant ..............................4-31
acceleration time......................................4-10, 4-30
acceleration (2) time .........................................4-30
acceleration stop...............................................4-25
actual-frequency monitoring.......................4-3, 4-97
ADD ..................................................................4-14
AHD ..................................................................4-59
AL .....................................................................4-60
alarm code output .............................................4-65
alarm relay terminal function.............................4-61
allowable under-voltage power failure
time .............................................................4-33
AM .............................................................2-7, 4-74
AMI ............................................................2-7, 4-74
analog command holding..................................4-59
analog input filter...............................................4-15
ascii mode.......................................................4-116
AT ..............................................................2-7, 4-12
ATR...................................................................4-98
automatic carrier frequency reduction...............4-44
automatic torque boost .....................................4-19
AVR...................................................................4-11
AVR voltage select...................................4-11, 4-15
B
basic display .....................................................4-77
base frequency .................................................4-11
BER ..................................................................4-82
binary operation .......................................4-48, 4-49
bit operation.............................................4-48, 4-49
BOK ..................................................................4-82
braking control ..................................................4-82
BRD .........................................................2-12, 4-46
BRD load factor monitoring.................................4-6
BRK ..................................................................4-82
C
capacitor life warning ........................................4-67
carrier frequency...............................................4-43
CAS ..................................................................4-58
CE ...................................................................2-19
CF1, CF2, CF3, CF4.........................................4-47
CM1 ...........................................................2-7, 2-21
commercial power supply switching..................4-53
communication function .........................4-67, 4-113
communication line disconnection
signal...........................................................4-67
constant-torque characteristic
(electronic thermal)......................................4-36
constant-torque characteristic (VC)..........4-16, 4-88
control circuit terminal.........................................2-7
control gain switching........................................4-58
control mode.....................................................4-16
cooling-fan operation ...............................4-45, 4-68
cooling-fan speed drop signal...........................4-68
copying .........................................4-94, Appendix-1
counterrotation prevention ................................4-91
CP1, CP2, CP3...............................................4-108
CS.....................................................................4-53
cumulative power monitoring ..............................4-4
cumulative power-on time monitoring........4-4, 4-65
cumulative running time...................................... 4-4
current position monitor...................................... 4-5
2CH .................................................................. 4-30
D
data comparison display...................................4-76
DB .................................................................... 4-20
DC braking .......................................................4-20
DC voltage monitoring........................................ 4-6
deceleration (2) time setting ............................. 4-30
deceleration and stopping at power
failure.......................................................... 4-84
deceleration curve constant.............................. 4-32
deceleration overvoltage restraint..................... 4-41
deceleration time .............................................. 4-10
derating ............................................................4-43
detection of terminal disconnection .................. 4-71
digital operator...........................................2-22, 3-3
display of trip monitoring..............................4-6, 5-9
DSE.................................................................. 4-96
DWN................................................................. 4-56
E
easy sequence ..........................................4-5, 4-95
electronic gear.......................................4-99, 4-101
electronic thermal ............................................. 4-37
electronic thermal overload monitoring............... 4-6
electronic thermal warning level setting............ 4-38
EMC ............................................safety instructions
emergency stop.................................................. 2-9
EMR ................................................................... 2-9
encoder pulse.........................................4-96,4-103
end frequency.........................................4-14,4-104
end-frequency rate ........................................... 4-15
energy-saver operation..................................... 4-32
excessive speed................................................. 5-5
extended function mode .....................................3-8
external analog input ........................................ 4-12
external DC braking.......................................... 4-20
external thermistor............................................ 4-72
external trip....................................................... 4-57
F
F/R.................................................................... 4-57
F-TM................................................................. 4-51
factory default(setting) .................................... 4-75
FA1, FA2, FA3, FA4, FA5.................................. 4-62
FBV .........................................................4-26, 4-29
feedback....................................................4-1, 4-28
feedback option................................................ 4-96
feed forward selection ......................................4-28
FM .............................................................2-7, 4-73
FOC.................................................................. 4-91
forcible operation.............................................. 4-51
forcible-terminal operation................................ 4-51
forcing............................................................... 4-91
forward rotation signal ...................................... 4-69
FOT ................................................................ 4-110
FR..................................................................... 4-68
free setting of electronic thermal
characteristic............................................... 4-38
free V/f characteristic........................................ 4-17
free-run stop..............................................4-9, 4-52