Hitachi SJ700B SERIES - Page 274

Index
Index - 3
O
O................................................................2-7, 2-21
O2.................................................... 2-7, 2-21, 4-12
O2Dc.................................................................4-71
OD ...........................................................4-28, 4-29
Odc ...................................................................4-71
offline auto-tuning .............................................4-85
OHF ..................................................................4-68
OI...............................................................2-7, 2-21
OIDc..................................................................4-71
OL, OL2 ............................................................4-40
OLR ..................................................................4-39
online auto-tuning .............................................4-87
ONT ..................................................................4-64
OPE ................................................... 3-3, 4-8, 4-51
operating methods ..............................................3-1
operation after option error ...............................4-79
operation frequency ..........................................4-13
operation mode.................................................4-33
operation time over signal
(RNT)/plug-in time over signal
(ONT) .................................................4-59, 4-64
operator ...................................................4-13, 4-66
ORG..................................................................4-99
ORL ..................................................................4-99
ORT .....................................................4-104, 4-110
OTQ..................................................................4-65
output current monitoring....................................4-1
output frequency monitoring ...............................4-1
output frequency setting......................................4-7
output signal delay/hold ....................................4-72
output voltage monitoring....................................4-3
overcurrent restraint..........................................4-41
overload notice advance signal................4-39, 4-40
overload restriction............................................4-39
overtorque.........................................................4-65
P
P/PI switching ...................................................4-58
P24 ............................................................2-7, 2-21
PCC ..................................................................4-59
PCLR ................................................................4-96
PCNT.........................................................4-5, 4-59
phase loss input.............................................. 4-36
phase loss input protection ............................. 4-36
PID....................................................................4-26
PIDC .................................................................4-29
POK ................................................................4-104
positioning completed .....................................4-104
position bias....................................................4-103
position command monitor..................................4-5
position range specification............................. 4-110
power monitoring ................................................4-3
PPI....................................................................4-58
process variable (PV), PID feedback
monitoring ............................................4-1, 4-29
program counter..................................................4-5
program number monitoring................................4-5
programming error monitoring ............................4-6
programmable controller...................................2-22
protective function...............................................5-1
pulse counter .............................................4-5, 4-59
pulse train frequency input..............................4-112
pulse train position command ...........................4-99
R
reduced-torque characteristic
(electronic thermal) ..................................... 4-39
reduced torque characteristic (VP) ................... 4-16
reduced voltage start........................................ 4-42
remote operation .............................................. 4-56
remote operator..................................... Appendix-1
reset ............................................2-9, 3-3, 4-9, 4-54
restart with input frequency......................4-33, 4-36
retry after trip.................................................... 4-33
retry selection................................................... 4-33
reverse rotation signal ..............................4-60,4-70
reversible.................................................4-13, 4-28
RNT.................................................................. 4-64
ROT................................................................ 4-110
rotation direction minitoring.................................4-1
rotational direction restriction.............................. 4-7
RS .............................................................2-9, 4-54
RUN....................................................3-3, 4-4, 4-60
running time over / power-on time over ...4-60, 4-64
run command source setting ..............................4-8
running signal................................................... 4-62
RV .................................................................... 4-46
RVR.........................................................4-60, 4-70
S
scaled output frequency monitoring.................... 4-2
2nd/3rd control ................................................. 4-50
secondary resistance compensation ................ 4-87
sensorless vector control.........................4-16, 4-89
servo-on ..........................................................4-111
SET, SET3........................................................ 4-50
SFT................................................................... 4-51
SF1, SF2, SF3, SF4, SF5, SF6, SF7................ 4-47
sign of the frequency to be added .................... 4-14
sink logic........................................................... 2-19
SJ300 .................................................... Appendix-1
slide switch SW1 ............................ 2-9, Appendix-1
SLV................................................................... 4-16
software lock.....................................................4-51
SON.................................................................4-111
source logic ......................................................2-22
SPD................................................................ 4-108
speed deviation maximum................................ 4-96
speed biasing ................................................. 4-103
speed/position switching................................. 4-108
STA................................................................... 4-57
stabilization constant ........................................ 4-79
start/end frequency setting for external
analog input ................................................4-14
start frequency.................................................. 4-14
start-frequency rate .......................................... 4-14
starting contact signal....................................... 4-68
start with matching frequency..................4-33, 4-52
STAT................................................................. 4-96
stop operation selection...................................... 4-9
STOP/RESET key selection ............................... 4-9
STP .................................................................. 4-57
synchronous operation ................................... 4-102