Honda Nighthawk CB 750 1995 User Manual

Guide to locating specific information within the manual using sections and index.

Explanation of symbols, callouts, and step-by-step instructions used in the manual.

Explanation of symbols used to indicate specific service procedures and precautions.

Safety precautions related to hazardous materials, hot components, and general workshop safety.

Details on identifying frame, engine, carburetor, and VIN numbers for the motorcycle.

Technical specifications for dimensions, frame, engine, drive train, and electrical systems.

General notes on maintenance, referring to other manuals and specifications.

Illustrates locations of parts requiring removal for specific maintenance tasks.

Scheduled maintenance intervals based on mileage and time intervals.

Notes on servicing the oil pump and oil pressure checks.

Common lubrication system issues like low oil level, low oil pressure, and warning light faults.

Step-by-step procedure for removing and installing the engine oil pump assembly.

Procedure for checking engine oil pressure using a pressure gauge.

Safety warnings and notes regarding fuel system service.

Diagnosing fuel system issues like engine won't start, lean/rich mixture, or poor performance.

Procedure for removing and installing the motorcycle's carburetors.

Procedure for adjusting the pilot screw for idle speed and emissions.

Notes on engine servicing and components requiring engine removal.

Detailed procedure for removing and installing the engine from the motorcycle frame.

Notes on camshaft service and hydraulic tappet system.

Diagnosing engine top-end issues like low compression, noise, and smoke.

Procedure for removing and installing the camshafts and related components.

Step-by-step guide for removing and installing the cylinder head assembly.

Notes on clutch maintenance and transmission oil impact.

Common clutch and gearshift issues like hard shifting or clutch slip.

Detailed procedure for disassembling the clutch assembly.

Procedure for removing and installing the gearshift linkage components.

Overview of crankcase separation, and components to remove.

Diagnosing crankshaft and transmission issues like noise, vibration, or hard shifting.

Procedure for removing the crankshaft and connecting rods.

Step-by-step guide for removing and installing the transmission assembly.

Safety precautions related to brake dust and servicing front suspension components.

Diagnosing front wheel, suspension, and steering problems like hard steering or wobbling.

Procedure for removing and installing the front wheel assembly.

Step-by-step guide for removing and installing the steering stem and bearings.

Safety warnings concerning brake dust and support requirements for servicing.

Diagnosing rear wheel and suspension issues like soft/hard suspension or wobbling.

Procedure for removing and installing the rear wheel assembly.

Step-by-step guide for removing and installing the swingarm assembly.

Safety precautions for brake system service, fluid handling, and contamination.

Diagnosing brake issues like soft/hard levers, dragging brakes, or squeaks.

Procedure for replacing the front brake pads.

Procedure for removing and installing the front brake master cylinder.

Procedure for removing and installing the front brake caliper.

Safety warnings regarding battery handling and electrical components.

Diagnosing battery overcharging and undercharging issues.

Procedure for removing and installing the motorcycle battery.

Steps for checking battery leakage and regulated voltage.

General notes on ignition system service and safety precautions.

Diagnosing ignition system faults like no spark or misfires.

Inspection and testing procedures for the ignition coils.

Procedure for checking and verifying ignition timing.

Safety warnings and component reference for the electric starter system.

Diagnosing starter motor issues like not turning, slow cranking, or no engine turn over.

Procedure for removing and installing the starter motor.

Safety notes for headlight bulb replacement and general component inspection.

Procedure for removing and installing the motorcycle's headlight assembly.

Procedure for removing and installing the speedometer and tachometer assembly.

Procedure for checking and replacing the neutral switch.

Complete electrical system wiring diagram for troubleshooting and reference.

Diagnosing starting issues: fuel flow, spark, compression, and wet plugs.

Diagnosing power loss: wheel spin, tire pressure, clutch, ignition, and tappet conditions.

Troubleshooting low speed performance: ignition timing, pilot screws, intake leaks, and spark.

Troubleshooting high speed performance: ignition timing, hydraulic tappets, and fuel flow.

Diagnosing handling issues: steering, wheel wobble, and motorcycle pulling to one side.