EasyManua.ls Logo

Honeywell Centraline LION - User Manual

Honeywell Centraline LION
54 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
LION Controller
Installation &
Commissioning
Instructions
Copyright © 2015 Honeywell GmbH ● All Rights Reserved EN1Z-0921GE51 R0315
3.4
LION
SYSTEM
INSTALLATION AND COMMISSIONING INSTRUCTIONS
CONTENTS
Safety Information ............................................................... 2
General Safety Information ............................................. 2
Safety Information as per EN60730-1 ............................. 2
System Overview ................................................................ 3
System Architecture ........................................................ 3
I/O Modules ..................................................................... 4
Interfaces and Bus Connections ..................................... 7
Technical Data ................................................................. 7
Planning ............................................................................... 8
Overview .......................................................................... 8
Transformer Selection ..................................................... 8
Fusing Specifications ...................................................... 9
System Protective Earth Grounding ................................ 9
Lightning Protection ......................................................... 9
Panel Bus Topologies ..................................................... 9
LONWORKS Bus Topologies ........................................... 10
C-Bus Topologies .......................................................... 10
Accessories ................................................................... 10
Cable Specifications ...................................................... 11
Dimensions .................................................................... 14
Mounting/Dismounting Modules ..................................... 16
Mounting/Dismounting Controller/Sockets .................... 16
Mounting/Dismounting Electronic Modules ................... 18
Mounting/Dismounting Manual Disconnect Modules .... 19
Mounting/Dismounting Auxiliary Terminal Packages ... 20
Mounting/Dismounting Cross Connectors .................... 21
Mounting/Dismounting Swivel Label Holders ............... 21
Wiring and Setting Up the System .................................. 22
General Safety Considerations ..................................... 22
Wiring Push-in Terminals .............................................. 22
Connecting Power Supply ............................................. 23
Connecting Single Bus Controller Systems .................. 24
Connecting Panel Bus and LONWORKS Bus Mixed
Controller Systems ........................................................ 25
Setting Address of Panel Bus I/O Modules ................... 27
Setting I/O Bus Switch ................................................... 27
Connecting Field Devices ............................................. 28
Commissioning I/O Modules ......................................... 29
Updating Software ......................................................... 29
Connecting to External Systems or Interfaces .............. 30
Connecting via LONWORKS Bus ..................................... 30
Connecting via C-Bus .................................................... 31
Connecting HMIs or Laptops ......................................... 31
Connecting Modems ...................................................... 31
Description of the CLLIONLC01 ....................................... 32
Overview ........................................................................ 32
Features ......................................................................... 33
Description of the I/O Modules ........................................ 38
Common Features ......................................................... 38
Troubleshooting ................................................................ 39
Testing Wiring Connections ........................................... 39
Troubleshooting on the CLLIONLC01 Controller .......... 39
Appendix 1: System Protective Earth Grounding .......... 43
LION Systems and SELV .............................................. 43
LION Systems and Standard EN60204-1 ..................... 43
Earth Grounding of EN60204-1 Applicable Systems .... 43
Appendix 2: Remote Communications ........................... 45
Approved Modems ......................................................... 45
Modem or ISDN Terminal Adapter Connection ............. 45
Modem Requirements.................................................... 45
Troubleshooting ............................................................. 45
Appendix 3: Sensor Characteristics ............................... 46
BALCO 500 .................................................................... 46
NTC 20 k ..................................................................... 47
PT 1000 .......................................................................... 48
NI1000TK5000 ............................................................... 50
NTC 10 kΩ ..................................................................... 51
PT 3000 .......................................................................... 52
Trademark Information
Echelon, LON, L
ONMARK, LONTALK, LONWORKS, Neuron, are
trademarks of Echelon Corporation registered in the United
States and other countries.

Table of Contents

Questions and Answers

  • J
    jennifer51Aug 15, 2025
    What to do if the Alarm LED is ON on my Honeywell Controller?
    • P
      plopezAug 15, 2025
      If the Alarm LED is ON in your Honeywell Controller, it could be due to a hardware problem, a fault in the application, or the controller starting without an application, or the operator manually stopped the application. Try powering down and then powering up the CLLIONLC01. If the problem continues, check and reload the application if necessary. If the issue still persists, consider replacing the hardware.
  • L
    Laura JohnsonAug 18, 2025
    Why is the Power LED flashing on my Honeywell Centraline LION Controller?
    • D
      daniel74Aug 18, 2025
      If the Power LED is flashing on your Honeywell Controller, it indicates that one or more of the internal voltage supplies are outside the permissible ranges, causing the controller to stop operating. Check the power and wiring. If the problem persists, consider replacing the hardware.
  • K
    Kimberly PerezAug 21, 2025
    How to fix LONWORKS Service LED issue on Honeywell Centraline LION Controller?
    • T
      Todd BuckAug 21, 2025
      If the LONWORKS Service LED is active at any time, this indicates that watchdog timer resets are occurring, which could mean there's a corrupt EEPROM and the system is in bootstrap mode. To resolve this, download the firmware.
  • E
    Eric AlvarezAug 25, 2025
    What does LONWORKS Service LED during power up/reset mean on Honeywell Centraline LION Controller?
    • J
      James SimpsonAug 25, 2025
      If the LONWORKS Service LED is active during power up or reset, it means the node lacks an application. This can be due to neuron chip firmware when a mismatch occurs on the application checksum. Set the module to 'configured online' using EXCELON. If the problem persists, and the MIP software on the LW interface has been erased due to a wrong setting performed using the ECHELON tool, replace the hardware.
  • B
    Barbara WestAug 27, 2025
    What does it mean if the Alarm LED is flashing on my Honeywell Centraline LION Controller?
    • A
      Alejandro HarveyAug 27, 2025
      If the Alarm LED is flashing on the Honeywell Controller once, it means that the controller has performed a restart. If it happens multiple times, there is an application or hardware problem.
  • H
    haysallenAug 30, 2025
    What to do if both HMI LEDs are OFF on Honeywell Centraline LION Controller?
    • L
      laura18Aug 30, 2025
      If both HMI LEDs are OFF, it indicates no HMI Interface communication. Check the HMI Interface connection and ensure proper earthing of connected hardware.
  • R
    riosmichaelSep 2, 2025
    What to do if both C-Bus LEDs are OFF on Honeywell Controller?
    • I
      Ian MartinSep 2, 2025
      If both C-Bus LEDs are OFF, it indicates no C-bus communication. Check the C-bus settings.
  • B
    baileycynthiaSep 5, 2025
    Why are both C-Bus LEDs flashing synchronously on my Honeywell Centraline LION Controller?
    • D
      Daisy GarciaSep 5, 2025
      If both C-Bus LEDs are flashing synchronously, this indicates no C-bus communication. Check the C-bus wiring.
  • C
    Christopher MackSep 8, 2025
    What does it mean when both Modem LEDs are OFF on a Honeywell Controller?
    • C
      Casey BairdSep 8, 2025
      If both Modem LEDs are OFF, it indicates no Modem Interface communication. Check the Modem Interface connection.
  • R
    ramoselizabethSep 12, 2025
    What causes the LONWORKS Service LED to light up after powering up Honeywell Centraline LION Controller?
    • E
      Emily NelsonSep 12, 2025
      If the LONWORKS Service LED is active after powering up the Honeywell Controller, it could indicate bad node hardware. Replace the hardware.

Summary

Safety Information

General Safety Information

Essential safety precautions for installation, operation, and maintenance of the LION System.

Safety Information as per EN60730-1

System data and compliance details according to the EN60730-1 standard.

System Overview

System Architecture

Diagram and explanation of the LION System's overall structure and components.

I;O Modules

Description of pluggable and mixed I/O modules, terminal sockets, and color coding.

Interfaces and Bus Connections

Details on connecting the LION System via Panel Bus, LONWORKS, C-Bus, HMI, and modem.

Planning the LION System

Planning Steps

Key considerations for planning the LION System installation, including power, fusing, and networking.

Transformer Selection

Guidance on selecting appropriate transformers based on current requirements for LION System components.

Fusing Specifications

Recommendations for selecting fuses for the CLLIONLC01, I/O modules, and active field devices.

Mounting and Wiring

Mounting;Dismounting Modules

Procedures for mounting and dismounting controller, I/O modules, and accessories.

Wiring and Setting Up the System

Instructions for wiring terminals, connecting power, and preparing the LION system.

Connecting Field Devices

Guidance on connecting field devices with power supply and proper cabling practices.

Controller and Module Descriptions

Description of the CLLIONLC01

Overview and front panel details of the CLLIONLC01 controller, including interfaces and LEDs.

Alarm and Power LEDs

Explanation of controller LEDs for status indication (power, alarm, watchdog) and troubleshooting.

Troubleshooting

Methods for diagnosing and resolving issues using controller LEDs, bus LEDs, and wiring checks.

Appendices

Appendix 1: System Protective Earth Grounding

Information on SELV compliance and EN60204-1 earth grounding requirements for LION Systems.

Appendix 2: Remote Communications

Instructions for establishing remote communication via modem or ISDN terminal adapter.

Appendix 3: Sensor Characteristics

Data tables detailing the characteristics of various sensors (BALCO 500, NTC, PT) used with the LION System.

Honeywell Centraline LION Specifications

General IconGeneral
BrandHoneywell
ModelCentraline LION
CategoryController
LanguageEnglish

Related product manuals