What to do if there is an FDAP failure on my Honeywell Wireless Access Point?
If you experience an FDAP failure with your Honeywell Wireless Access Point, it indicates a hardware issue. The suggested solution is a hardware replacement, as any failure within the FDAP necessitates this action.
General| Manufacturer | Honeywell |
|---|---|
| Wireless Standard | IEEE 802.11 a/b/g/n |
| Ingress Protection Rating | IP67 |
| Product Type | Wireless Access Point |
| Category | Wireless Access Point |
| Frequency Bands | 2.4 GHz and 5 GHz |
| Antennas | 2 x external dual-band antennas |
| Operating Temperature | -40°C to +75°C |
| Mounting | DIN-rail, wall, or pole |
| Security | WPA2-Enterprise |
| Protocols | Modbus TCP, EtherNet/IP |
| Certifications | ATEX, IECEx |
| Weight | 0.5 kg |
Details changes made to the document across revisions.
Specifies the target users for this guide, including roles like Plant Managers.
Lists assumed knowledge for operating the OneWireless network and related systems.
Outlines the topics covered in the guide for user orientation.
Lists other documents containing additional information for deploying the OneWireless network.
Explains the Field Device Access Point's role and function in industrial wireless networks.
Describes different FDAP models like backbone router and field router functionalities.
Details the physical components and enclosure of FDAP Gen3 and FDAP Gen3 Anchor.
Describes the physical components and enclosure of the FDAP2 model.
Highlights key functionalities such as power options, antenna diversity, and Ethernet.
Covers security aspects like encryption, authentication for FDAP Gen3 and Gen3 Anchor.
Directs users to relevant documentation for regulatory compliance details.
Lists essential steps and considerations before installing an FDAP in a wireless network.
Instructions for checking the availability and condition of FDAP hardware before installation.
Guidance on determining optimal locations for FDAP deployment in a wireless network.
Steps for connecting antennas to FDAP Gen3 and FDAP Gen3 Anchor for optimal performance.
Procedures and requirements for properly grounding the FDAP for safety and regulatory compliance.
Instructions for mounting FDAP Gen3, Gen3 Anchor, and FDAP2 units in various locations.
Detailed steps for connecting power cables to FDAP Gen3, Gen3 Anchor, and FDAP2.
Procedures for terminating Ethernet cables for FDAP connectivity.
Steps to connect FDAP devices to the Wireless Device Manager (WDM).
Explains the process of authenticating and adding an FDAP to the network using WDM.
Details the configuration parameters available for FDAP devices in the OneWireless user interface.
Introduces the FEWIO solution for integrating legacy Modbus devices into the OneWireless system.
Provides a graphical overview of the FEWIO solution with FDAP Gen3.
Steps to convert an FDAP router into a FEWIO device using WDM.
Instructions for connecting Modbus TCP devices to FDAP Gen3/Gen3 Anchor configured as FEWIO.
Instructions for connecting Modbus RTU devices to FDAP Gen3/Gen3 Anchor configured as FEWIO.
Steps to configure FEWIO devices within the Wireless Device Manager (WDM).
Guide on setting up and inspecting Modbus registers for FEWIO devices.
Steps to convert a FEWIO device back to an FDAP router.
Information on integrating FEWIO devices with the Experion system.
Explains methods for monitoring FDAP status and performance in the network.
How to use topology maps in the OneWireless UI to check device connectivity and signal quality.
Using a handheld device to monitor FDAP status and parameters.
Monitoring system events generated by FDAP devices for troubleshooting.
Generating and viewing reports on FDAP connectivity and device health.
Procedure for replacing a failed FDAP with a new device.
Steps to remove a failed FDAP from the network.
Information on upgrading FDAP radio firmware over-the-air.
Methods for diagnosing problems with FDAP devices, including events and logs.
How to access and use system logs for troubleshooting FDAP issues.
Steps to recover FDAP functionality after a suspected failure.
Detailed technical specifications for FDAP Gen3.
Detailed technical specifications for FDAP Gen3 Anchor.
Detailed technical specifications for FDAP2.
Installation control drawing for FDAP Gen3 and FDAP Gen3 Anchor.
Reference labels for FDAP Gen3 devices.
To Next Page
