Honeywell FIre-LITe ALArms MS-9600LS - Legacy ACM Series Annunciators

208 pages

To Next Page

To Previous Page

60 MS-9600LS Series Manual — P/N 52646:B2 2/12/2010

Installation Optional Modules and Devices

Legacy ACM Series Annunciators

ACM and AFM Series Annunciators provide visual indications of FACP status in remote locations.

Refer to the appropriate annunciator manual for information on installation, wiring and operation.

Main Page

Table of Contents5
Section 1: Product Description13
Inventory13
Features and Options13
Specifications15
1: Current Availability17
Controls and Indicators17
Circuits18
Components19
1: Intelligent Addressable Detectors: Newer Series20
2: Intelligent Addressable Modules: Newer Series20
3: 300 Series Intelligent Addressable Devices20
4: Addressable Device Accessories20
Optional Modules21
Accessories21
1: PS-Tools Programming Utility21
2: Dress Panel: DP-969222
3: TR-CE Trim Ring22
4: Battery Box22
5: Battery Charger22
6: New ANN-BUS Annunciators/Devices23
ANN-BUS Wiring23
ANN-BUS Device Addressing26
Remote Fire Annunciator27
ANN-S/PG Serial/Parallel Interface Installation30
ANN-I/O LED Driver Module32
ANN-LED Annunciator Module34
ANN-RLY Annunciator Module36
ANN-BUS Audio Panel Control38
7: Legacy ACS Annunciators40
Getting Started40
Section 2: Installation42
Mounting42
Power46
1: AC Power and Earth Ground Connection46
2: Battery Power46
3: Special Application DC Power Output Connection47
Relays47
Notification Appliance Circuits47
1: Configuring Nacs48
2: Style y (Class B) NAC Wiring49
3: Style Z (Class A) NAC Wiring49
Power-Limited Wiring Requirements50
Optional Modules and Devices51
1: DACT-UD2 Installation52
2: 4XTMF Transmitter Module Installation55
3: Auxiliary Trouble Input (J16 & J17)57
4: SLC-2LS Expander Module57
5: Printer/Pc58
6: Annunciators59
Legacy ACM-8RF Relay Control Module59
Legacy ACM Series Annunciators60
Section 3: Programming61
Programming Data Entry61
User Programming62
Initial Power-Up63
Programming Screens Description63
Programming and Passwords63
Master Programming Level65
1=Autoprogram66
2: Point Program67
Detector Programming67
Module Programming78
3=Zone Setup95
Enable95
Disable96
Zone 97, 98 and 9996
Zones Installed97
Zones Enabled97
Zones Disabled97
Zone Type98
Zones Available99
4: Loop Setup99
Loop Selection99
Loop Protocol100
5: System Setup100
Trouble Reminder101
Banner101
Time-Date103
Timers105
NAC (Notification Appliance Circuit)107
Relays112
Canadian Option113
Waterflow Silenceable114
6: Verify Loops114
7: History115
View Events115
Erase History115
8: Walktest116
9: Option Modules117
Annunciators/Udact118
On Board DACT134
Printer/Pc134
10: Password Change135
11: Clear Program136
12: Program Check137
Maintenance Programming Level138
1: Disable Point139
2=History140
3: Program Check141
4: Walktest142
5: System143
6: Zone Setup144
Zones Installed146
Zones Enabled146
Zones Disabled147
Zone Type147
Zones Available148
Zone Message149
Section 4: Operating Instructions150
Panel Control Buttons150
1: Acknowledge/Step150
2: Alarm Silence150
3: Drill/Hold 2 Sec150
4: Reset150
LED Indicators150
Normal Operation151
Trouble Operation152
Alarm Operation153
Supervisory Operation154
Process Monitor Operation155
Hazard Condition Operation155
Medical Alert Condition Operation156
Programmed Zone Operation156
Disable/Enable Operation156
Waterflow Circuits Operation156
Detector Functions156
Time Functions: Real-Time Clock157
NAC Operation157
Synchronized NAC Operation157
Coded Operation157
Presignal158
Positive Alarm Sequence158
Special System Timers159
1: Silence Inhibit Timer159
2: Autosilence Timer159
3: Trouble Reminder159
4: Waterflow Retard Timer159
5: Alarm Verification159
Walktest160
Read Status160
3=Power161
1=System Point162
2=Zones163
4: Trouble Reminder165
5: Timers165
6: Nac166
7: Relays166
8: Program Check167
9: History167
10: Annunciators167
11: Phone Line169
12: Central Station169
13: Service Terminal170
14: Printer/Pc170
15: Print171
16: Time-Date173
Section 5: Power Supply Calculations174
Overview174
Calculating the AC Branch Circuit174
Calculating the System Current Draw174
2: How to Use Table 5.3 on Page 176 to Calculate System Current Draw175
Calculating the Battery Size177
1: NFPA Battery Requirements177
2: Selecting and Locating Batteries177
Appendix A: Software Zones178
A.1: Correlations178
Appendix B: Default Programming186
Appendix C: NFPA Standard-Specific Requirements187
C.1: Central Station/Remote Station Transmitter: Connection to FACP Dry Contacts193
C.2: MBT-1 Municipal Box Trip - Silenceable194
Appendix D: FACP with Keltron195
Appendix E: Wire Requirements196
E.1: NAC Wiring197
Appendix F: HVAC Control198
F.1: Control Module Operation198
F.1.1: Hvac Shutdn198
F.2: Monitor Module Operation198
F.2.1: Hvac Restart198
F.2.2: Hvac Ovrride199
Appendix G: Canadian Application200
Index201

Honeywell FIre-LITe ALArms MS-9600LS - Legacy ACM Series Annunciators

Table of Contents

Other manuals for Honeywell FIre-LITe ALArms MS-9600LS

Related product manuals