Need help?Do you have a question about the Honeywell Fire-Lite Alarms MS-9050UD and is the answer not in the manual?
General| Brand | Honeywell |
|---|---|
| Model | Fire-Lite Alarms MS-9050UD |
| Category | Control Panel |
| Language | English |
Lists NFPA codes relevant to fire alarm systems, including NFPA 72 and NFPA 70.
Lists UL standards applicable to fire alarm system components and control units.
Lists manufacturer-specific documents for device compatibility and installation.
Explains connections for audible and visual notification devices (NACs).
Details the Signaling Line Circuit connection for addressable devices.
Describes system relay outputs and PC connection for utilities.
Lists and describes devices connected via the ANN-BUS communication circuit.
Refers to addressable devices, SLC wiring, and the 4XTMF transmitter module.
Highlights major features like built-in DACT, SLC loop, device capacity, NACs, relays, and programmer.
Details AC power requirements, voltage, and wire specifications.
Covers battery requirements, SLC loop details, and NAC specifications.
Lists specifications for relays, EIA-232, and ANN-BUS interfaces.
Describes the FACP's LCD display, keypad layout, and function keys.
Explains the meaning of FACP status LEDs and the onboard sounder.
Explains the SLC loop for addressable device communication.
Lists output circuits (Charger, NACs) and details the FACP's relays.
Describes DACT functions like line seizure, dialing, and supported communication formats.
Covers the Main Circuit Board, Cabinet, and Batteries specifications.
Details addressable detectors, modules, and related accessories like EOL resistors.
Details the 4XTMF module for municipal box transmission and reverse polarity.
Covers the PK-CD programming utility and dress panel/trim ring accessories.
Describes battery box options for housing batteries and chargers.
Details the CHG-75 and CHG-120F external battery chargers.
Lists optional devices that connect to the FACP ANN-BUS circuit.
Explains wiring calculations, addressing, power, and connection diagrams for ANN-BUS devices.
Covers ANN-80 electrical specs, mounting, and opening procedures.
Provides detailed steps for connecting the ANN-80 annunciator to the FACP.
Covers specs, installation, and connection of the ANN-S/PG module.
Details connecting and configuring the PRN-6F printer.
Covers the ANN-I/O board layout, terminals, and electrical specifications.
Details connecting the ANN-I/O to the FACP and wiring LEDs to the module.
Covers the ANN-LED board layout, terminals, and electrical specifications.
Illustrates connecting the ANN-LED module to the FACP ANN-BUS.
Covers ANN-RLY board layout, specs, and mounting instructions.
Illustrates connecting the ANN-RLY module to the FACP ANN-BUS.
Provides a brief summary of minimal steps for bringing the MS-9050UD online.
Details phone line requirements, DACT connection, and FCC compliance.
Covers telephone company rights and warnings regarding service and connection.
Covers general cabinet mounting, backbox installation, and semi-flush mounting.
Details installing the main circuit board assembly into the FACP backbox.
Details AC power connection, wire requirements, and earth ground connection.
Explains battery connection, polarity, and safety warnings.
Covers FACP relays and NAC configurations (Style Y/Z).
Describes separation of power-limited and nonpower-limited wiring within the cabinet.
Illustrates DACT installation and wiring for two phone lines.
Details the installation of the 4XTMF transmitter module, including jumper settings.
Covers data entry methods, user levels, and navigation through programming screens.
Details initial setup, passwords, and data saving procedures.
Covers automatic device detection and manual configuration of points (detectors, modules).
Details zone setup, enabling/disabling, special zones, and SLC loop style/protocol.
Covers system-wide settings like timers, NACs, relays, Canadian option, and loop verification.
Explains how to view/erase history and perform system walktests.
Covers enabling the ANN-BUS and configuring installed modules (ANN-80, ANN-S/PG, ANN-I/O, ANN-LED, ANN-RLY).
Covers enabling the DACT and configuring primary/secondary phone line types.
Configures reporting enable, backup options, call limits, station numbers, test settings, and formats.
Allows enabling/disabling points and viewing/erasing system event history.
Checks program integrity and performs system walktests.
Configures system time/date and zone settings.
Explains the operation of panel buttons like Acknowledge, Silence, Drill, and Reset.
Describes the meaning of the FACP's status indicators and LEDs.
Describes system status and indications during normal and trouble conditions.
Details system behavior for Alarm, Supervisory, Process Monitor, Hazard, and Medical Alert conditions.
Details event transmission priority and reporting format structures for central stations.
Covers enabling remote download, passwords, and system security during data transfers.
Details calculating AC branch circuit and total system current draw.
Covers calculating battery size and meeting NFPA standby power requirements.
Explains software zone setup and provides an example of device-to-zone correlations.
Lists minimum components and requirements for NFPA 72 compliance across different system types.
Details wire types, gauges, distances, and impedance for SLC and ANN-BUS circuits.
Provides tables for maximum wire length for NAC circuits based on load and wire gauge.
Details programming control modules for automatic HVAC fan shutdown during fire alarms.
Explains using monitor modules to restart fans or override shutdown procedures.
Describes the Contact ID transmission string structure and lists event codes.
Provides specific installation instructions for ANN-LED annunciators in Canada.
Details AC power connection requirements for Canadian FACP models.
To Next Page