Honeywell Lynx Plus Programming Guide

- 3 -
To Initialize Download ID and Subscriber Account Number for Downloading:
✻96 Resets all subscriber account numbers and CSID in preparation for an initial download.
To Load a Default Set:
✻97 Enter a number 1-4 corresponding to the selected default table (See the Installation Instructions for the
default tables). Enter 0 if you are not selecting a default table.
To Exit Programming Mode:
✻98 Exits programming mode and prevents re-entry by: Installer Code + 8+ 0 + 0. If ✻98 is used to exit
programming mode, system must be powered down, then press [✻] and [#] within 50 seconds of power
up to re-enter programming mode.
✻99 Exits programming mode and allows re-entry by: Installer Code + 8 + 0 + 0 or: Power-up, then press [✻]
and [#] within 50 seconds of power up.
DATA FIELDS
Data Field Display Function& Programming Options [ ] = Programmed Table 1 Default Values
SYSTEM SETUP (✻20– ✻30) † Entering a number other than the one specified may give unpredictable results.
20
2020
20
INSTALLER
INSTALLER INSTALLER
INSTALLER CODE
CODECODE
CODE
Installer Code
[4112]
Enter 4 digits, 0–9
21
2121
21
QUICK
QUICK QUICK
QUICK ARM
ARM ARM
ARM ENABLE
ENABLEENABLE
ENABLE
Quick Arm Enable
† [1]
0 = no; 1 = yes
22
2222
22
KEYPAD
KEYPAD KEYPAD
KEYPAD BACKLIGHT
BACKLIGHTBACKLIGHT
BACKLIGHT
Keypad Backlight Timeout
[0]
0 = none (backlighting always on); 1 = backlight off after 10secs
23
2323
23
FORCED
FORCED FORCED
FORCED BYPASS
BYPASSBYPASS
BYPASS
Forced Bypass UL installations = 0
† [0]
0 = none; 1 = bypass open zones
24
2424
24
RF
RF RF
RF HOUSE
HOUSEHOUSE
HOUSE ID
ID ID
ID CODE
CODECODE
CODE
RF House ID Code
| [00]
00 = disable all wireless keypad usage; 01–31 = 5804BD/5804BDV house ID
25
2525
25
X10
X10 X10
X10 HOUSE
HOUSE HOUSE
HOUSE CODE
CODECODE
CODE
Powerline Carrier Device (X10) House ID
[0]
0 = A; 1 = B, 2 = C, 3 = D, 4 = E, 5 = F, 6 = G, 7 = H, 8 = I, 9 = J, #10 = K, #11 = L,
#12 = M, #13 = N, #14 = O, #15 = P
26
2626
26
CHIME
CHIME CHIME
CHIME BY
BY BY
BY ZONE
ZONEZONE
ZONE
Chime By Zone
† [0]
0 = no; 1 = yes (program zones to chime on zone list 3)
27
2727
27
CLOCK
CLOCK CLOCK
CLOCK DISPLAY
DISPLAYDISPLAY
DISPLAY
Real Time Clock Display
† [1]
0 = no; 1 = yes, display time on keypad
29
2929
29
DST
DST DST
DST MNTH
MNTH MNTH
MNTH STR/END
STR/ENDSTR/END
STR/END
Daylight Saving Time Start/End Month
[3, 11]
Start End
1-9, #+10,#+11,#+12. Enter 0,0 if no daylight savings time used.

Honeywell Lynx Plus Specifications

General

Model	Lynx Plus
Battery Backup	Yes
Voice Prompts	Yes
Installation	DIY or professional
User Codes	8
Display	LCD
Keypad	Built-in
Siren	Built-in
Compatibility	Honeywell 5800 series wireless devices
Panel Type	Self-Contained Wireless Security System
Warranty	2 years