Honeywell SEK001 User Manual

User Instructions for the
Sensor Evaluation Kit, SEK001, for Use with
TruStability™ RSC Series and Digital Output
Versions of the HSC Series and SSC Series Board
Mount Pressure Sensors
32324959
Issue B
Sensing and Internet of Things
1.0 OVERVIEW
The Sensor Evaluation Kit, SEK001, along with the readily-
available components shown in Table 1, and the free evaluation
software available on Honeywell’s website, comprise a simple
set of components used to evaluate Honeywell TruStability
RSC Series and the digital output versions (SPI or I
2
C) of the
TruStability HSC Series and SSC Series Board Mount Pressure
Sensors.
The SEK001 allows the user to obtain sensor readings without
needing to develop any code. The sensor to be evaluated
is mounted into the receiving sockets on the SEK001. The
SEK001 is then plugged in as a shield board to the Arduino™
Uno Rev3 Microcontroller Board. Honeywell evaluation
software, downloaded to the user’s PC, controls the Arduino
Uno Rev3 to take sensor readings that are then displayed on
the PC’s screen.
The readings may also be recorded to a .csv file for further
analysis, and, in the case of the RSC Series, used in the
equations found in the RSC Series datasheet.
In addition to being mounted directly on the SEK001, the
sensor may also be remotely connected to the SEK001 via wire
leads, allowing the sensor to be tested in adverse environments,
or in a prototype product for proof of concept testing.
2.0 SEK001 AND USER-PROVIDED COMPONENTS
2.1 Assemble the components shown in Table 1.
Table 1. Sensor Evaluation Kit Contents and User-Provided Items
1
Honeywell Sensor Evalution Kit, SEK001 User-Provided Components
Includes:
• Sensor Evaluation Board
• Five jumpers for HSCDRRN001ND2A5 preconfigured on board
Arduino Uno Rev3 Microcontroller Board (A000066)
USB Interface Cable (Type A Male to Type B Male)
PC with Internet access
(Note: If using a docking station computer, ensure that the
computer is not in its docking station when installing and
running the software.)
1
The Honeywell RSC, HSC or SSC Series pressure sensor is not included with the SEK001. The user must purchase the sensor
separately.
Jumper
Jumpers

Honeywell SEK001 Specifications

General

Manufacturer	Honeywell
Model	SEK001
Form Factor	Mini-ITX
Chipset	Intel Q170
Max Memory	32GB
Operating Temperature	0°C to 60°C
Socket Type	LGA 1151
Memory Slots	2
Memory Type	DDR4
Storage Interface	SATA III, M.2
USB Ports	6 (USB 3.0)
LAN	Gigabit Ethernet

Summary

1.0 Overview

2.0 SEK001 and User-Provided Components

2.1 Assemble Components

Details the assembly of the SEK001 kit and user-provided components as listed in Table 1.

2.2 Sensor Selection

Guides users to select the appropriate sensor for evaluation and access corresponding datasheets.

2.3 Connect Sensor to SEK001

Explains how to mount the selected sensor onto the SEK001 evaluation board, referencing jumper configuration.

2.4 Connect SEK001 to Arduino Uno Rev3

Details the process of connecting the SEK001 board to the Arduino Uno Rev3 to create the evaluation assembly.

3.0 Download and Install Software and Firmware

3.1 Software and Firmware Installation

Provides step-by-step instructions for downloading and installing the necessary software and firmware for the SEK001.

4.0 Software Screens

4.1 Sensor Selection Panel Screen

Describes the interface for selecting the sensor type, series, and part number for evaluation.

4.2 Measurement Screens

Details the screens used for displaying and capturing sensor measurement data, including HSC/SSC and RSC series.

4.3 Configuration Screen

Explains the configuration screen for setting data format, sample rate, and offline data storage options.

4.4 Help Screen

Provides access to software information, getting started guides, and contact support details.

Appendix A. SEK001 Specifications

Appendix B. Remote Connection

Appendix C. Jumper Configurations

Appendix D. SEK001 External Features and Dimensions