Honeywell T7200 - Program the Thermostat

63-4038—7 12
Program the Thermostat
OVERVIEW
The keyboard is located behind the thermostat flip-up
cover. See Fig. 18. There are 16 keys to set, review and
modify programmed times and temperatures. The liquid
crystal display (LCD) shows day, time or temperature and
which programming period is operating.
The thermostat can be set for two occupied and two
unoccupied time and temperatures for each day of the week
(28 independent settings). The two override keys provide
quick temporary programming changes for increased occu-
pant comfort.
IMPORTANT: To program the thermostat, 24 Vac is re-
quired (turn on system power) and the keyboard lock-
out switch (see Fig. 27) must be in the ON-KEYBD
position.
Fig. 18—Thermostat programming keys and
LCD display.
OCCUPIED •
UNOCCUPIED •
CONT UNOC •
3 HR OCCUPIED •
11:32
HEAT
AM
SET SET START TIME
SET TEMPERATURE DATA CHANGE
OVERRIDE
CLOCK
DAY
SELECT
DAY
COPY
OCCUPIED
START TIME
UNOC
START TIME
OCCUPIED
HEAT
UNOC
HEAT
OCCUPIED
COOL
UNOC
COOL
DISPLAY
CLEAR
START TIME
+
–
3 HOUR
OCCUPIED
CONT
UNOC
M4384
SET CURRENT TIME/DAY
1. Set the current time by pressing and releasing the
CLOCK key once.
2. Press the + or - key until the current time appears on the
LCD.
3. Set the current day by pressing and releasing the DAY
key once.
4. Press the + or - key until the current day appears on the
LCD.
NOTE: Su=Sunday; Mo=Monday; Tu=Tuesday; We=
Wednesday; Th=Thursday; Fr=Friday; Sa=Saturday.
SET PROGRAM TIMES
IMPORTANT: The thermostat will remain in occupied
mode from the point of initial programming until it
encounters the first unoccupied start time. To avoid
the unnecessary occupied period following initial pro-
gramming, set a 12:00 AM unoccupied start time on
the thermostat when programmed.
NOTE: The programming times are in intervals of ten
minutes; i.e., 8:00, 8:10, 8:20.
1. Press the SELECT DAY key. The display shows the
abbreviation for a day.
2. Press and hold the + or - key until the desired day
appears.
3. Press the OCCUPIED START TIME key. The pro-
gram indicator will point to OCCUPIED.
4. Press and hold the + or - key until the desired start time
appears.
NOTE: Anytime a start time is not required, press the
CLEAR START TIME key.
5. Press the UNOC START TIME key. The program
indicator will point to UNOCCUPIED.
6. Press and hold the + or - key until the desired start time
appears.
7. To program a second occupied start time for the
selected day, repeat Step 3 until four dashes (----) are dis-
played or the second start time (if previously programmed) is
displayed. Then repeat Step 4.
8. To program a second unoccupied start time for the
selected day, repeat Step 5 until four dashes (----) are dis-
played or the second start time (if previously programmed) is
displayed. Then repeat Step 6.
9. Repeat Steps 1 through 8 for each remaining day of the
week or refer to the following section, COPY A DAY.
COPY A DAY
1. Press the SELECT DAY key. The display shows the
abbreviation for a day.
2. Press and hold the + or - key until the day to be copied
from appears.
3. Press the COPY key.
4. Press and hold the + or - key until the day to be copied
to appears.
NOTE: The day to be copied from will remain on the display.
5. Press the COPY key a second time to perform the
copy.
6. Repeat Steps 3 to 5 to copy to another day.
SET PROGRAM TEMPERATURE SETPOINTS
NOTE: The setpoint temperature range is 45°F (unoccupied
heat) to 95°F (unoccupied cool). The occupied heat setpoint
must be at least 2°F less than the occupied cool setpoint.
1. Press the SET TEMPERATURE key (OCCUPIED
HEAT, OCCUPIED COOL, UNOC HEAT, or UNOC
COOL). The program indicator will point to OCCUPIED or
UNOCCUPIED and the LCD will indicate HEAT or COOL.
T7200/T7300/Q7300
PROGRAM THE THERMOSTAT