To Next PageTo Next PageHow to fix a Honeywell TP30WKNR when the continuous drain is not working?
If you've connected the continuous drain but water isn't draining from your Honeywell Dehumidifier, try raising the front of the unit by ½ to 1 inch (1.27 cm to 2.54 cm). This helps ensure proper drainage through the back hose.
How to troubleshoot a Honeywell TP30WKNR Dehumidifier that does not start?
If your Honeywell Dehumidifier isn't starting, first ensure it has electricity. Then, check that the power cord is correctly plugged in. Finally, make sure the water tank is properly positioned, as the unit won't operate if it's not securely in place.
What to do if the Honeywell TP30WKNR says 'Water Tank Full' and is beeping?
If the 'Water Tank Full' indicator is on and your Honeywell Dehumidifier is beeping, the water tank is likely full; empty it. Also, ensure the water tank is correctly positioned in the unit and that the floater inside the tank is properly aligned.
What to do if there is water on the floor near my Honeywell Dehumidifier?
If you find water on the floor near your Honeywell Dehumidifier, first check the connections of the garden or drain hose to ensure they are tight. If you're using the water tank, disconnect the continuous drain hose and replace the rubber stopper and drain cap.
What does error code E5 mean on my Honeywell TP30WKNR Dehumidifier?
If 'E5' appears on your Honeywell Dehumidifier, ensure the Auto Drain Pump Tube and Cap are correctly installed onto the Drain Outlet, with the seal washer properly in place. Verify the Direct Drain Outlet is clean. Confirm you're using the correct Auto Drain Tube (16ft/5m). Ensure the Auto Drain Pump Cap is secure. If the error persists, unplug the unit, drain the water manually, and restart. If 'E5' reappears, contact the consumer service center.
Why does frost appear on the coils of my Honeywell TP30WKNR Dehumidifier?
If frost appears on the coils of your Honeywell Dehumidifier, especially after turning it on in low room temperatures (below 41°F (5°C)), this is normal. The frost should disappear within an hour or so after switching the dehumidifier OFF.
What does P1 error mean on a Honeywell TP30WKNR Dehumidifier?
If 'P1' appears on your Honeywell Dehumidifier (TP70PWK / TP70PWKN / TP70PWKNR models), ensure the water tank is correctly positioned. The unit will not operate until the tank is secure.
Why is my Honeywell TP30WKNR running but not decreasing humidity?
If your Honeywell Dehumidifier is running but the humidity level isn't decreasing, try these steps: * Lower the humidity level setting. * Ensure all doors and windows are closed and sealed. * Eliminate other humidity sources in the room. * Ensure the room temperature is between 41°F (5°C) and 89°F (32°C). * Clean the dust filter. * Remove any blockages from the air outlet or intake.
Why does my Honeywell TP30WKNR Dehumidifier run constantly and not stop?
If your Honeywell Dehumidifier runs constantly, it might be due to the area being too large for the unit's capacity. Consider adding another dehumidifier for larger spaces. Also, ensure all windows and doors are tightly sealed to prevent new moisture from entering.
Why is my Honeywell TP30WKNR Dehumidifier blowing cold air?
The air temperature from the top vent of your Honeywell Dehumidifier depends on the room environment and other factors, it can fluctuate and this is normal. No action required.
General| Model | TP30WKNR |
|---|---|
| Type | Dehumidifier |
| Energy Star Certified | Yes |
| Noise Level | 51 dB |
| Continuous Drain Option | Yes |
| Coverage Area | Up to 1500 sq ft |
| Color | White |
| Capacity | 30 pints |
| Filter Type | Washable filter |
| Operating Temperature | 41°F to 89°F |
Guides for downloading the app and connecting the dehumidifier.
Safety guidelines for electrical connections, cords, and handling.
Guidelines for proper placement, usage by individuals, and transportation.
Explanation of safety symbols related to R32 refrigerant.
Important warnings and precautions for appliances with R32 refrigerant gas.
Regulations and guidelines for unit transportation, marking, and storage.
Explanation of how the dehumidifier functions to remove moisture.
Important information about the optimal operating temperature range.
Instructions for initial unit placement and refrigerant stabilization.
Recommendation to operate in an enclosed area for optimal efficiency.
Guidelines for temperature, clearance from objects, and level floor placement.
Explanation of how room air circulation and enclosure affect performance.
Instructions for removing securing tape from the unit.
Steps for removing and replacing the splash guard and accessories.
Note on the foam float's function and proper positioning.
Identification of various parts of the dehumidifier unit.
Identification of included accessories like drain tubes and caps.
Step-by-step guide for installing the cord winder permanently.
Description and labeling of all controls on the unit's panel.
Information specific to Wi-Fi and voice control features.
Note on the Auto Drain Pump mode availability and function.
How to turn the dehumidifier ON and OFF using the power control.
Instructions for setting and adjusting the desired humidity level.
How to activate and use the continuous operation mode.
Explanation of the water tank full indicator and its function.
Setting auto-off and auto-on timers for the dehumidifier.
Explanation of the two fan speed settings (High and Low).
How the filter alert works and how to reset it after cleaning.
How to activate and use the sleep mode for reduced display brightness.
The indicator light for Wi-Fi connectivity status.
How to activate and use the auto drain pump for continuous drainage.
Warning about the auto drain pump's behavior after a power outage.
Explanation of the automatic defrost process for internal coils.
Step-by-step guide to emptying the water tank.
Instructions for connecting and using the continuous water drain tube.
How to check and fix leaks in the continuous drain tube connection.
Proper positioning of the drain tube for effective water flow.
How to use the auto drain pump for continuous water removal.
Instructions for connecting the auto drain pump tube to the unit.
Checking for leaks and securing the auto drain pump tube.
How to activate the pump function and its indicator light.
Important note about not using drain tubes longer than provided.
General guidelines for cleaning the appliance and its parts.
Instructions for cleaning and maintaining the dust filter.
Procedures for storing the dehumidifier when not in use.
Solutions for when the dehumidifier fails to start.
Troubleshooting steps for when humidity levels do not decrease.
Reasons and solutions for the unit running continuously or not stopping.
Troubleshooting when the water tank full indicator is on and unit beeps.
Explanation for cold air blowing from the top vent.
Explanation and solution for frost appearing on the unit's coils.
Troubleshooting for issues with continuous drain functionality due to uneven surfaces.
Causes and solutions for water leaks on the floor.
Explanation of normal operational noises from the fan and compressor.
Solution for error code P1 related to water tank positioning.
Action to take for humidity sensor failure (error code EH).
Action to take for temperature sensor failure (error codes E1/E2).
Troubleshooting for refrigeration system protection errors (E3).
Solutions for abnormal pumping drainage errors (E5).
FCC compliance and interference guidelines for the device.
Industry Canada compliance and interference guidelines.
Information about ENERGY STAR qualification and energy efficiency.
