What to do if the bar code is displayed but not entered by my Honeywell Scanner?
If the bar code is displayed but not entered into your application, you likely need to program a suffix. Programming a suffix enables the Honeywell Scanner to output the bar code data along with the necessary key (like “CR”) to enter the data.
What to do if the bar code is displayed but not entered into the application by my Honeywell Scanner?
If the bar code is displayed but not entered into the application, you likely need to program a suffix. Programming a suffix enables the Honeywell Scanner to output the bar code data along with the necessary key (like “CR”) to enter the data.
Why won't my Honeywell Scanner read the bar code?
If your Honeywell Scanner won’t read your bar code, start by scanning the sample bar codes in the back of the manual. If the scanner reads those, then check that your own bar code is readable and that its symbology is enabled. If it still fails, scan All Symbologies.
How to fix a Honeywell Scanner that won't read bar codes?
If your Honeywell Scanner won’t read your bar code, start by scanning the sample bar codes in the back of the manual. If the scanner reads those, then check that your own bar code is readable and that its symbology is enabled. If it still fails, scan All Symbologies.
Why is my Honeywell Scanner not reading symbols well?
If the Honeywell Scanner isn’t reading symbols well, check these items: * The scanner window is clean. * The symbols aren’t smeared, rough, scratched, or exhibiting voids. * The symbols aren’t coated with frost or water droplets. * The symbols are enabled in the scanner or in the decoder to which the scanner connects.
What to do if Honeywell Scanner is not reading symbols well?
If the Honeywell Scanner isn’t reading symbols well, check these items: * The symbols aren’t smeared, rough, scratched, or exhibiting voids. * The symbols aren’t coated with frost or water droplets. * The symbols are enabled in the base or Access Point to which the scanner connects.
Why is the green LED not illuminated on my Honeywell Scanner?
If the green LED on your Honeywell Scanner isn’t illuminated, verify the following: * The scanner is correctly placed in the base. * There is external power or 12 volt host power. * Charge mode is turned on. * The battery is not bad or deeply discharged.
What to do if the red LED isn't illuminated on Honeywell Scanner?
If the red LED isn’t illuminated on your Honeywell Scanner, check that: * The power cable is connected properly and there is power at the power source. * The host system power is on (if external power isn’t used).
How to fix the aimer if it isn't illuminated on Honeywell Scanner?
If the aimer isn’t illuminated on your Honeywell Scanner, verify that: * The cable is connected properly. * The host system power is on (if external power isn’t used). * The trigger works.
General| Operating Temperature | 0°C to 40°C (32°F to 104°F) |
|---|---|
| Drop Specifications | Designed to withstand 30 1.5 m (5 ft) drops to concrete |
| Storage Temperature | -40°C to 60°C (-40°F to 140°F) |
| Humidity | 0% to 95% relative humidity, non-condensing |
| Connectivity | USB, RS-232, Keyboard Wedge |
| Decode Capability | 1D barcodes |
| Scan Pattern | Area Image |
| Motion Tolerance | 10 cm/s (4 in/s) for 13 mil UPC at optimal focus |
| Light Levels | 0 to 100, 000 lux |
| Scanner Type | Area-Imaging Scanner |
Overview of the User's Guide for Voyager scanners.
Guidance on connecting scanners and bases to host systems.
Setting and resetting custom scanner configurations.
Quick setup for common interfaces using Plug and Play codes.
Selecting keyboard layouts for different countries and languages.
Settings for Baud Rate, Word Length, Handshaking, and Timeouts.
Pairing and managing scanner connection with Bluetooth devices.
Establishing connections between scanners and bases/access points.
Details on battery charging, recommendations, safety, and disposal.
Storing and transmitting barcode data when out of range.
Managing host acknowledgment of scanned data.
Settings for beeper volume, pitch, and LED for good reads.
Options for in-stand sensor, poor quality codes, and CodeGate.
Configuring reread delays, character activation, and deactivation.
Understanding how prefixes and suffixes build message strings.
Procedures for adding or removing prefix/suffix entries.
Introduction to the editor for changing scanner output.
Commands for cursor movement and searching within message data.
Enables or disables decoding of all supported barcode symbologies.
Setting valid reading lengths for barcode symbologies.
Configuration for Code 39 symbology, including On/Off, Start/Stop, Check Char, Length, Append, PARAF, Full ASCII, Code Page.
Configuration for UPC-A symbology.
Explains Keyboard Function Code, Hex/ASCII, and CTRL+X relationships.
PC-based programming functions for scanners, including installation.
Restores scanner settings to original factory defaults.
Details the structure and parameters of menu commands.
Activating and deactivating the scanner with serial commands.
Detailed specifications for the Voyager 1450g scanner.
Detailed specifications for the Voyager 1452g cordless scanner.
Pin assignments for Keyboard Wedge, Serial Output, and USB cables.
Instructions for cleaning the scanner window and housing.
Guide to identifying and resolving corded scanner issues.
Guidelines for troubleshooting cordless scanner and base issues.
Contact methods for installation and troubleshooting support.
Terms and conditions of the Honeywell product warranty.
Lists AIM and Honeywell identifiers for symbologies.
Mapping ASCII control characters to keyboard functions.
Visual examples of various barcode symbologies and their data.
Barcodes representing digits 0 through 9.
Barcodes representing letters A through F.
To Next Page
